What's so special about Browning Hi-Power?

In 1962, the design was modified to replace the internal extractor with an external extractor, improving reliability. Standard Hi-Powers are based on a single-action design. Unlike modern double-action semi-automatic pistols, the Hi-Power's trigger is not connected to the hammer .

What is the difference between Browning Hi-Power and 1911?

While both JM Browning designs, the Hi-Power is a double stack 9mm, whereas the 1911 is a single stack . 45ACP . Both are legendary firearms and one could hardly go wrong with either one.

Is Browning Hi-Power good for concealed carry?

And while I do generally prefer DA/SA for concealed carry, the Hi Power offers something the Beretta doesn't: It's not huge. With a shorter grip than most full-sized guns, the Hi Power is better suited for concealed carry . In fact, the Hi Power is fairly compact, overall.

Who uses the Browning Hi-Power?

The Browning HI Power was used by Britain, Canadian and by Germany (captured when they invaded Belgium). The Browning was not an issue weapon to U.S. forces. It's quite possible American soldiers could have used one captured from a German soldier but that would have been fairly rare.

Is the Browning Hi-Power still good?

The Browning Hi-Power is insanely ergonomic for 1935, and those good ergonomics still hold in 2021 .

What is a Browning Hi-Power worth?

Conclusion: Grading 100% 70% MSR $1,245 $1,125 $500 MSR $1,245 $1,125 $500 MSR $1,245 $1,125 $500

What gun is similar to Browning Hi-Power?

The FN P35 Hi-Power The MC P35 pays tribute to the John Browning design that was finished by noted engineer Dieudonné Saive. The original P35 was a single-action locked-breech handgun with a then-pioneering double-stack magazine. The FN P35 earned an excellent reputation as a reliable and useful handgun.

What caliber is good for concealed carry?

380 ACP allows for comfortable concealment and lightweight carry. This caliber is commonly chosen by individuals who prioritize concealability and are willing to accept a trade-off in effectiveness. It's important to note that shot placement becomes crucial when relying on the . 380 ACP for self-defense.

What militaries used the Browning Hi-Power?

In hands and holsters The Browning Hi-Power eventually found its way into the hands of both Axis and Allied forces. The Belgian military adopted it first, and shortly after that, Canada licensed the design for its military.

When was Browning Hi-Power made in Belgium?

The Browning Hi-Power is a semi-automatic pistol first made by John Browning, then finished by FN Herstal (a Belgian gun company) in 1935 after Browning's death. There are 9x19mm Parabellum models and . 40 S&W models of the gun.

Is the Browning Hi-Power single stack?

The Browning Hi-Power is a double-stack , hammer-fired, and single-action 9mm handgun, which was originally designed by John Moses Browning, the godfather of the firearms world, in 1926.

Why is the Browning machine gun so good?

The M2 fires the .50 BMG cartridge, which offers longer range, greater accuracy, and immense stopping power. The closed bolt firing cycle made the M2 usable as a synchronized machine gun on aircraft before and during World War II, as on the early versions of the Curtiss P-40 fighter.

Is the Browning Hi-Power accurate?

They are very accurate (as are almost all handguns if you train enough) and perfectly reliable. At least mine is so far. Never had a hammer bite either. But I talked to somebody who was bitten by the slide of a Glock I think if you have big hands, it could certainly happen with the High-Power.

(PDF) LISLE GARTHWAITE BROWNING HI-POWER C.B. … · GARTHWAITE BROWNING HI-POWER ARMORER’S TOOLS The Right Tools For Proper Disassembly & Assembly #100-007-006AS Browning Hi-Power Armorer’s

l g

smit

h t

PAGE 480 Office/Tech: 641-623-5401SATISFACTION GUARANTEED

SINCE 1939

SPE

CIA

LTY

N T

Ample range for 28 ga. to 12 ga. Flex-drive eliminates chatter, gouging. For 1/4" or larger electric drill. Included in choke set. abSPECS: 1/4" (6.3mm) shaft, 81/2" (21.6cm) long.

BARREL HONE EXTENSION SHAFT - Piloted shaft attaches to your electric hand drill motor and accepts Brownells Barrel Hones. Keeps the hone in the center of the bore; prevents expensive dam-age; lets the hone do all the work for faster, better looking results. Includes abrasive paper holder and a threaded adapter that ac-cepts all 5/16"-27 tpi shotgun brushes and mops.#080-915-000AS Barrel Hone Extension Shaft,

8K66D46 � � � � � � � � � � � � � � � � � � � � � � � � � � $ 78.99

LISLE

SHOTGUN BARREL HONE

#531-108-002AS No. 2 Barrel Hone, 1C14P99� � � � � � � � � �$ 14.99#531-107-602AS No. 2-S Stones, only, 1C3H99 � � � � � � � � 3.99

Brings Bores & Chokes Back to New-Or-Better Polish

No. 2-S

SPE

CIA

LTY

N T

Five, precision-machined gunsmith punches equip you to handle a wide variety of any pistol disassembly and reassembly jobs. Nontapered, with a flat tip for removing solid pins—excellent for drifting sight pins in and out. Kit includes four, steel punches through-hardened for maximum strength and a non-marring brass drift punch for jobs where the gun’s finish must be protected. Knurled handles ensure a firm grip to prevent slippage and protect your gun’s finish from scratches and scuffs. abSPECS: Pin punches - 4140 chrome-moly steel. 1/16", 3/32", 1/8", 5/32" diam-eters. 31/2" to 41/2" OAL. Drift punch - Brass. 31/4" (8.3cm) long x 3/16" (4.8cm) diameter.

LYMAN PISTOL PUNCH SET

#539-000-019AS Pistol Punch Set, 5K15M39 � � � � � � � � � � �$ 16.99

Most Common Sizes Used On Pistol Projects

Selected by noted pistolsmith

Jim Garthwaite, these are the right tools for complete disassembly and reassembly of your Hi-Power. Jim’s innovative Hammer/Sear Installation Tool is part of the Kit and is also available separately. Machined out of solid aluminum, it’s designed to compress and re-tain the mainspring to help make sear installation easy and fast. The aluminum construction ensures it won’t scrape or gouge the frame. Complete Armorer's Kit includes the Hammer/Sear tool, plus four pin punches, aluminum frame spacer, correct-size miniscrewdriver for magazine catch-lock, and complete disassembly/ assembly in-structions that explain how to use the tools. abSPECS: Kit includes Hammer/Sear Installation Tool; small screwdriver; 1/16", 5/64", and 3/32" roll pin punches, 3/32" flat pin punch, aluminum frame spacer, and instructions.

GARTHWAITE BROWNING HI-POWER

ARMORER’S TOOLSThe Right Tools

For Proper Disassembly &

Assembly

#100-007-006AS Browning Hi-Power Armorer’s Tool Kit, 6C73E94 � � � � � � � � � � � � � � � � � � � � � � $ 79.95

#100-007-008AS Hammer/Sear Installation Tool, 6C22A93 � � � � � � � � � � � � � � � � � � � � � � � � � � 24.95

Cross-slotted tip fits the elevation and windage screws on Millet pistol sights. Help eliminate gouging and marring of the screws. abSPECS: 11/2" (3.8cm) long.

MAGNA-TIP® MILLET REAR SIGHT BITFits Perfectly; Won’t Blemish The Sight

#080-147-000AS Millet Rear Sight Bit, 8K3A72 � � � � � � � � � �$ 4.99

One convenient kit with the most needed tools for SIG mainte-nance. Designed for the police armorer and professional gunsmith, each tool in the kit has been thoroughly field tested. ab

#080-451-017AS #17 Screwdriver, 8K10B78 � � � � � � � � � � � $ 11.99

⑮ SIG SIGHT MOVER - Easy, no-mar, rear sight adjustment.#584-045-220AS SIG Sight Mover, 4H117N88 � � � � � � � � �$ 129.99

⑯ ANGLE POINT TWEEZERS - Puts pins in tight places.#345-415-634AS Angle-point Tweezers, 5D6N89 � � � � � � $ 6.89

⑰ COTTON APPLICATORS - Clean nooks and crannies.#885-861-500AS 500 Cotton-Tipped Applicators,

8K7M49 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 8.99

⑱ CLP-16 BREAK-FREE - For cleaning and lubrication.#102-100-023AS Break-Free CLP, 2/3 fl. oz. Bottle,

6K3B92 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 4.99

⑲ SIG COMBO TOOL - For grip screws, plus remove and install mainspring, magazine catch stop, sear spring.#719-100-000AS SIG Combo Tool, 9A42C35 � � � � � � � � � $ 44.99

⑳ TOOL BOX - Durable, high impact plastic.#696-100-303AS Tool Box, 6F13K09 � � � � � � � � � � � � � � � � � � $ 17.59

① #3 ROLL PIN PUNCH - For P220, P225, P226, P228 slide.#230-100-003AS #3 Roll Pin Punch, 8K4A21 � � � � � � � � � � � $ 4.99

② #4 ROLL PIN PUNCH - Removes Firing pin retainer.#230-100-004AS #4 Roll Pin Punch, 8K4D21 � � � � � � � � � � $ 4.99

③ 3MM CUP TIP PUNCH - For firing pin positioning pin.#080-620-300AS Long 3mm Cup Tip Punch,

8K10Q80 � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 11.99

④ SHORT 3MM CUP TIP PUNCH - Starter punch for firing pin positioning pin.#080-620-301AS Shrt 3mm Cup Tip Punch, 8K11M32 � � �$ 12.99

⑤ STARRETT 1/16" PUNCH - Remove hammer stop pin, sear spring pin.#827-525-780AS 1/16" Punch, 7B6I99 � � � � � � � � � � � � � � � � � � �$ 6.99

⑥ STARRETT 1/8" PUNCH - Use as a slave pin.#827-525-800AS Starrett Pin Punch, 8K5K99 � � � � � � � � � � �$ 5.99

⑦ STARRETT 3/32" PIN PUNCH - Use as sear shaft slave pin.#827-525-790AS #3 Roll Pin Punch, 7B6B29 � � � � � � � � � � �$ 6.49

⑧ BROWNELLS 5/64" PIN HOLDER - Holds the breech pin.#080-685-078AS 5/64" Roll Pin Holder, 8K13Q14 � � � � � � � �$ 14.99

⑨ BROWNELLS 3.5MM PIN HOLDER - Holds various pins.#080-685-130AS 3.5mm Roll Pin Holder, 8K12D84 � � � � �$ 14.99

⑩ 3 NYLON DRIFT PUNCHES - Install P229 extractor.#080-478-000AS Set of 3 Nylon Front Sight Punches,

8K4C43 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 4.99

⑪ PISTOL BENCH BLOCK - No-mar nylon provides a solid sur-face, with large through holes, for driving pins, polishing.#080-000-493AS Pistol Bench Block - Blue, 8D19E99 � �$ 19.99

⑫ 1" NYLON/BRASS HAMMER - Brass head for driving various pins. No-Mar nylon head is ideal for “tapping”.#818-600-100AS 1" Nylon/Brass Hammer Combo,

8A19B99 � � � � � � � � � � � � � � � � � � � � � � � � � � �$ 19.99

⑬ #2 FIXED BLADE SCREWDRIVER - Remove extractor on P229, P236, P239 stainless steel slide.#080-451-002AS #2 Screwdriver, 8K10F78 � � � � � � � � � � � � $ 11.99

⑭ #17 FIXED BLADE SCREWDRIVER - For grip screws.

TOOLS FOR SIG HANDGUNS

1514

#080-220-100AS SIG Kit Tools, w/Tool Box, 8K273C91 � � � � � � � � � � � � � � � � � � � � � � � � $ 296.99

#080-220-101AS SIG Kit Tools, No Tool Box, 8K258A52 � � � � � � � � � � � � � � � � � � � � � � � � 281.99

The Tools You Need To Fix SIGs

Correctly

Here are the three Magna®-Tip bits you’ll need to install and remove our custom grip screws. Although we picked them to match our screws, they’ll fit other brands too. abSPECS: Steel, heat treated. Allen: 3/32" hex. Slotted: 240-5. TORX: T-15. Fit Brownells 1911 Auto and Ruger MkI/MkII grip screws.

GRIP SCREW BITSAllen®, TORX® & Slotted

Bits Fit Right

#080-185-100AS 3/32" Allen Bit, 8K2I66 � � � � � � � � � � � � � � � � �$ 2.99#080-240-540AS #240-5 Slotted Bit, 8K2B66 � � � � � � � � � � � 2.99#080-435-015AS T15 Torx Bit, 8K2I66 � � � � � � � � � � � � � � � � � � 2.99

High-density polymer block supports S&W M&P and Glock polymer-framed pistols without marring and helps with armory work and disassembly. Special design relieves pressure from critical function surfaces and gives easy access to all pins. Moveable bosses quickly adjust to hold different size frames. Holes and slots accom-modate thumb safety and magazine disconnect. Fixed bosses — one for .45 and the other for 9mm/.40/.357 — hold striker to ease striker spring removal and installation. Special trigger bar block makes it easy to swap triggers. Armorer’s Tray attaches to the underside of the block, elevating the work surface nearly an inch, while the in-terior and embedded magnet keep pins and small steel parts from rolling away. Raised edges in the center support the muzzle when taking off slide back plates. Comes with a 1/16" Allen wrench for the rear sight screw and a 1/8" roll pin punch that seats into coil roll pins in M&P frames and drives the pins far enough to be out of the way but not ejected. Storage slots in the tray for punch and wrench. abSPECS: Polymer, red. Block - 7" (17.7cm) long, 4" (10cm) wide, 1½" (3.8cm) high. Tray - 7" long, 4" wide, .9" (2.3cm) high.

APEX TACTICAL POLYMER ARMORER’S BLOCK & TRAY

Supports Polymer-Framed Pistols For Armory Work & Disassembly

Block (Gun Not Included)

#100-011-660AS Polymer Armorer’s Block, 7F27C00 � � $ 29.99#100-014-075AS Polymer Armorer's Tray, 7F22Q37 � � � 24.99

We designed this block especially for hand-gun work, so it's just the right size to give you a solid, stable working surface for almost any pis-tol and revolver. Special cutouts fit the slides of today’s most popular semi-autos, including the Colt 1911 and clones, S&W® M&P®, Glock®, and Springfield XD. Opposite side has deep “V” notches for holding barrels, plus different-sized holes and cutouts to aid you in driving out pins and other small parts, including dedicated holes/cutouts for striker disassembly on Glock/M&P, M&P extractor pin removal, and for removal of 1911 hammer strut, barrel link pin, ejector pin, maga-zine catch, and grip bushing. All that - in one tool! Made of tough, scrape-resistant, non-marring PVC that can be drilled or modified to meet your specific needs. So handy, you'll want several - one for the bench, another for the field tool kit, range bag, etc. abSPECS: Machined PVC, black. 4" (10cm) dia. 11/2" (3.8cm) high.

UNIvERSAL PISTOL ARMORER'S BLOCKSolid Working Surface For

A Variety Of Pistols

#080-001-261AS Univ. Pistol Armorer's Block , 8K33L29 � �$ 39.99

High-strength polymer magazine well insert fits double-stack Beretta, SIG, and Taurus pis-tols. Slides into the mag well and locks tight using the factory latch, so the other end of the block can be clamped in a vise. Supports the pistol for cleaning, maintenance, and other servicing, while it keeps both hands free to do the work. Durable, injection-molded polymer composite construction won’t mar or scratch gun and resists most common cleaning solvents. To ensure a snug fit in your pistol, the ridge on the back of the stem may need to be filed down. abSPECS: Polymer, black. Stem – 45/16" (11cm) long. Fits Beretta 92/96, SIG P226/228/229, and Taurus PT-99/-101.

Secure, Hands-Free Support Of Pistol For

Cleaning & Maintenance

#100-005-890AS Beretta/SIG/Taurus Vise Block, 6B34M06 � � � � � � � � � � � � � � � � � � � � � � � � � � $ 39.99

C.B. GIORNESTO BERETTA/SIG/TAURUS

vISE BLOCK

Specialized pliers allow Glock owners to remove the base pad

from factory magazines without gouging or cracking the plastic. Small crimping tips contact the magazine precisely above the lock-ing tabs. Hardened, steel handles feature the correct geometric cur-vature to prevent over-compression of the magazine sidewalls. abSPECS: Steel, black finish. 6" (15.2cm) long.

MAGAZINE TOOL FOR GLOCK®

Removes Base Pads Fast, Without Damage

#080-000-191AS Magazine Tool For Glock, 8K20E06 � � $ 22.99

PAGE 481Orders/Tech: 800-741-0015order on the web

brownells.com

SPE

CIA

LTY

N T

Superb collection of professional quality tools that makes re-building and repair of the 92 Series easier and more cost efficient. Designed for the police armorer and professional gunsmith, these high-quality tools will perform the tasks required, time and again, without failure. Because of the rugged dependability and simplicity of the Beretta 92 design only a very few specifically-designed tools are needed to keep these great pistols shooting. Each and every tool included in this kit has been thoroughly tested, and many perform specific tasks recommended in the factory repair manual and are not available anywhere else. Following is a brief description of each tool contained in the Kit and the function it performs. And remem-ber, when you buy the entire kit, you save both time and money. ab

⑧ 1/4"BRASS DRIFT PUNCH - A harder-than-nylon but softer-than-steel punch for drifting fixed sights without damage.#080-920-102AS Brass Drift Punch, 8K4I37 � � � � � � � � � � � � $ 4.49

⑨ BERETTA MAGAZINE LIP GAUGE - Gives a clear check of minimum/maximum magazine lip width for correct feeding.#080-920-103AS Magazine Lip Gauge, 8K32J90 � � � � � � �$ 39.99

⑩ SERIES II INDIA STONE - Great for smoothing the Beretta's sear and hammer engagement surfaces.#080-815-000AS Series II India Stone, 8K14A45 � � � � � � � $ 20.99

⑪ TRIGGER RETURN SPRING TOOL - Installs trigger return spring. Keeps hands close to the work.#080-000-288AS Trgr Return Sprg Tool, 8K9M84 � � � � � $ 12.99

⑫ SERIES II HARD ARKANSAS STONE - Ultra-fine-grit stones for smoothing the Beretta's sear and hammer engagement surfaces.#080-815-001AS Series II Hard Arkansas Stone,

8K70D15 � � � � � � � � � � � � � � � � � � � � � � � � � � $ 79.99

① BERETTA GRIP BUSHING STAKER - Securely stakes grip bushing without frame damage. Matches factory stake.#080-920-101AS Beretta Grip Bushing Staker,

8K28C72 � � � � � � � � � � � � � � � � � � � � � � � � � � $ 36.99#080-920-010AS Replacement Bushing Staker Head,

only, 8K26G34 � � � � � � � � � � � � � � � � � � � � � 29.99

② 4 OZ. BALLPEEN - Correct size and weight for driving pins, brass drift punch, etc.#956-000-002AS 4 oz. Ballpeen Hammer, 9D29E99 � � � �$ 29.99

③ BERETTA BUSHING DRIVER BIT - Fits our MAGNA-TIP® handles to fully support the Beretta Stock Bushing.#080-920-100AS Beretta Bushing Driver Bit, 8K7L65 � � � $ 9.99

④ CLIP-TIP LAW ENFORCEMENT HANDLE - Short and small to keep hands close to the work. Clip-Tip shank minimizes bit wobble.#080-088-001AS Clip-Tip Law Enforcement Handle,

8K11I81 � � � � � � � � � � � � � � � � � � � � � � � � � � � � �$ 15.99

⑤ #300-5 MAGNA-TIP® BIT - Fits the Beretta grip screw.

⑥ 90° SCRIBE - Very handy for reaching down inside frame re-cesses to help maneuver smaller parts and springs.#345-080-090AS 90° Scribe, 8K4F99� � � � � � � � � � � � � � � � � � $ 4.99

⑦ BERETTA PIN PUNCHES - Sized to fit the metric roll pins on the Beretta 92 Series pistols. Set includes four punches.#080-092-114AS 3mm Pin Punch, 8K11L82 � � � � � � � � � � � $ 15.99#080-092-074AS 2mm Pin Punch, 8K11Q82 � � � � � � � � � � 15.99#080-092-055AS 1.5mm Pin Punch, 8K11Q82 � � � � � � � � � 15.99#080-092-059AS 1.5mm Starting Punch, 8K11B82 � � � � � 15.99#080-092-000AS Beretta Punch Set, 8K39L98 � � � � � � � � 50.99

TOOLS & KITS FOR BERETTA 92

Every Tool That's Required For Making Complete Repairs In Both The Shop & Field

The Right Tools For Entire 92 Series – Military & Civilian

#080-920-000AS Beretta 92 Series Tool Kit, Complete w/Tool Box, 8K216G29 � � � � � � � � � � � � �$ 219.99

#080-920-110AS Beretta Flat Storage Box, 8K13M85 � � 14.99

5 6

Tray

Specialized tool designed by the factory allows the user to restore older magazines to original specs and tune new magazines for maximum reli-ability. Prevents damage to delicate feed lips often caused by makeshift tools. abSPECS: Steel, black matte finish. 43/4" OAL. Includes complete instructions.

HIGH STANDARD .22 LR PISTOL

MAGAZINE LIP ADJUSTMENT TOOLCorrects Feeding Problems

#430-000-569AS Magazine Lip Adjustment Tool, 3D32D24 � � � � � � � � � � � � � � � � � � � � � � � � � � �$ 39.99

These compact, model-specific field maintenance packs pro-vide the soldier or law enforcement personnel with all the tools required to field strip, repair, and maintain tactical pistols while on the move. These are not run-of-the-mill generic tool kits, but care-fully selected, high-quality field armorer tools dedicated to specific weapons. Individual pouches and compartments inside the water- and abrasion-resistant Cordura® nylon case keep tools secure and separated to help minimize noise that could jeopardize your mis-sion. Nylon grab handles for easy carry, and quiet #9 YKK zippers with oversize pulls make it fast and easy to get tools in and out. Front panel features clear I.D. card sleeve and loop strip for name tape. ab

SPECS: Contents: M&P rear sight tool, S&W armorer’s fixed blade screw-driver, 1/16" Allen head driver, nylon/brass hammer, blue pistol bench block, cleaning brush, #3 (3/32") & #4 (1/8") steel roll pin punches, and 1/16" steel starter punch, plus .092", .078" and . 470" diameter steel cup tip punches and nylon case. Approx. 3 lb. 3 oz. (1.4 kg) wt.#080-000-039AS S&W M&P Field Pack, 8K196P60 � � � � $ 247.99

FIELD PACK CASE - The same, heavy-duty, Cordura field case in-cluded with our Weapons Field Maintenance Packs. Made available separately for your additional tactical gear and accessories.SPECS: Denier Cordura nylon, O.D. green. 12" (30.5cm) long, 101/2" (26.7cm) high, 31/2" (8.9cm) thick.#080-000-459AS Field Pack Case, Only, 8K69C66 � � � � � $ 75.99

1911 AUTO FIELD PACK - Keep your 1911 Auto in peak working order while out on patrol. Every tool has a purpose, and the com-plete kit allows full field stripping, so pistol can be properly cleaned, repaired, and parts replaced if needed.SPECS: Includes: #81 MAGNA-TIP® screwdriver handle w/ #120- 3, #185-00, #185-1, #240-5, T15 Torx, and bushing driver bits; grip bushing staker; lug iron; bushing wrench; plunger tube crimper kit; safety detent depres-sor; trigger stirrup die; nylon/brass hammer; pistol bench block; (3) nylon punches; front sight staking tool; extractor removal tool; .092" and .120" dia. brass push punches; mainspring housing pin pusher; 12"x24" bench/field gun mat. 5 lb. 2 oz. (2.32 kg) wt.#080-000-456AS Brownells 1911 Auto Field Pack,

8K324L54 � � � � � � � � � � � � � � � � � � � � � � � � $ 376.99

BERETTA 92/M9 FIELD PACK - All the tools you need for com-plete field stripping of your Beretta service pistol for maintenance, cleaning, and parts replacement. Includes roll pin punches, grip bushing driver bit, grip bushing staker, trigger return spring tool, and magazine lip gauge all specific to the 92/ M9—plus, India and Arkansas stones for smoothing hammer and sear engagement surfaces.SPECS: Includes: MAGNA-TIP® Law Enforcement clip tip screwdriver handle w/#300-5 slotted bit & #240-2 bushing driver bit; 4 oz. ball peen hammer; magazine lip gauge; grip bushing staker; flat & concave maga-zine lip forming pliers; straight/90 degree scribe; trigger return spring tool; (4) roll pin punches; 1/4" brass drift punch; India stone; and hard Arkansas stone. Approx. 5 lb. (2.3 kg) wt.#080-000-469AS Beretta 92/M9 Field Pack,

8K303H85 � � � � � � � � � � � � � � � � � � � � � � � � $ 329.99

GLOCK® FIELD PACK - Maintains the Brownells Field Pack go any-where philosophy, while including a nice array of dedicated tools for keeping any Glock model in peak working order. Includes mag-azine tool specifically designed for easily removing Glock floor-plates, rear sight mover, channel liner replacement tool, slide cover plate for installing Ghost-brand tactical triggers, and the Glok Blok vise block, plus roll pin punches, flat-tip screwdriver, front sight nut driver, .050" hex head wrench for adjustable rear sights, and an array of handy nylon cleaning brushes.SPECS: Contents - MAGNA-TIP® screwdriver handle with #120-3 slotted bit, 1/16" hex head bit, 3/32" & 3/16" pin punch bits, and Glock sight nut bit; Glok Blok vise block; sight adjustment tool; magazine tool; channel liner tool; chain nose pliers; armorer’s orange slide cover plate; .050" hex wrench; magazine brush; 9mm, .40 cal. & .45 cal. nylon bore brushes; double-ended parts cleaning brush; and 4 fl. oz. (118ml) bottle of Break-Free CLP. Case - 1000 denier Cordura nylon, O.D. green. 111/2" (29.2cm) long, 81/2" (21.6cm) high, 3" (7.6cm) thick.#080-000-582AS Field Tool Pack for Glock,

8K284E31 � � � � � � � � � � � � � � � � � � � � � � � � $ 304.99

S&W M&P FIELD PACK - All the tools required to field strip, repair, and maintain Smith & Wesson’s popular M&P semi-auto pistol. Includes the proprietary M&P rear sight removal tool, all neces-sary roll pin punches, an S&W fixed-blade armorer’s screwdriver, cleaning brush and other tools to keep your M&P working under difficult conditions.

HANDGUN FIELD MAINTENANCE PACKComplete, Dedicated Kits For Field Repair & Maintenance Of

Tactical Pistols

1911 Auto Field Pack shown

Precision-made tools that will take care of most any field repair on the entire family of Glock pistols. Kit includes: 3/16" nut driver for front sight re-moval; .050" Allen wrench for rear sight removal, installation and adjustment; 3/32" takedown punch. Tools feature hardened shafts and aluminum handles in a vinyl pouch. abSPECS: Shaft - steel, blued. Handle - aluminum, anodized red. 33/4" (9.5cm) long. 3/16" Nut Driver available separately.

ARO-TEK™

ARMORER'S TOOLS FOR GLOCK®

Every Tool You Need To Work On A GLOCK Pistol

#066-800-200AS Tool Kit, for Glock, 6F39K34 � � � � � � � � $ 45.00#066-800-300AS 3/16" Nut Driver, 6F21K86 � � � � � � � � � � � � 25.00

Built specifically for Glock pistols, our punch kit features a tip that is easily replaced if it ever bends or breaks. Punch is ideal for remov-ing the locking block pin, trigger housing pin, trigger pin, and can be used to depress the magazine floorplate catch. Handle is made of fatigueproof C.R.S. steel, with a tensile strength of over 140,000 psi, and includes a knurled-chuck to hold the tip securely in place. Replaceable tips are made of tool steel, and oil hardend to Rc 58-60, with beveled heads annealed to Rc 42-45. Kit includes one handle and one tip. Additional replacement tips are sold separately. abSPECS: Handle 3" (7.6cm) long x 3/8" (9.5mm) diameter. Pins are 2" (5.1cm) or 21/2" (6.3cm) long.

REPLACEABLE PIN PUNCH for GLOCK

Saves You From Buying All New Pin Punches

#080-001-121AS Replaceable Pin Punch Kit-Glock , 8K8K66 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 9.99

#080-001-120AS Replaceable Pin Punch Pin-Glock , 8K3J83 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4.99

Easy-to-use tool helps you remove factory front sights and in-stall aftermarket sights. The punch is just the right size for depressing front sight center spreader; hex wrench holds and tightens the small retaining nut for the replacement sight. Non-slip knurled grip. abSPECS: Delrin® handle. Steel punch and wrench. Black. 3/32" (2.3mm) punch. 51/4" (13.3cm) long. Will not work for models 17L, 34, 35, 24 and 24C.

B&J MACHINE

COMBINATION TOOL FOR GLOCK®

Handy Tool Makes Glock Sight Changes Easier

#694-301-100AS Combination Sight Tool for Glock, 4F18C72 � � � � � � � � � � � � � � � � � � � � � � � � � � � �$ 22.95

Original Glock factory disassembly tool lets you

completely disassemble any Glock pistol. Assists in removal locking block pin, trigger housing pin, and trigger pin. Depresses magazine floorplate catch for removal of plate for cleaning or replacement of spring and follower. Hardened steel pin shaft with deeply ridged, easy-to-grasp polymer handle.SPECS: Steel with polymer handle, black. 33/4" (9.5cm) O.A.L. 13/8" (3.5mm) shank length. .100" (2.5mm) shank diameter.

DISASSEMBLY TOOL FOR GLOCK®

Makes Stripping Your Glock Fast & Easy

#100-005-935AS Disassembly Tool, 1D6L93 � � � � � � � � � � � � $ 7.99

Completely disassemble any Glock pistol with this handy punch. Large wooden handle lets you to comfortably push out the locking block, trigger housing, and trigger pins. Tool is also ideal for disassembling the magazine floorplate. ab

GRACE USA DISASSEMBLY TOOL for GLOCK®

Lets You Easily Disassemble Any Glock Pistol

#354-000-039AS 3/32" Punch Glock®, 4E9K09 � � � � � � � � � � �$ 9.99

PAGE 482 Office/Tech: 641-623-5401SATISFACTION GUARANTEED

SINCE 1939

SPE

CIA

LTY

N T

Multi-function tool lets you do a complete disassembly, change sights, replace parts, even give your favorite Glock a quick brushing off. Features a 3/32" pin punch, 3/16" flat blade for connector removal, 3/16" sight nut driver and a cleanup brush. Pocket clip for handy carry. abSPECS: Brass body, stainless steel pin punch. 5" (12.7cm) O.A.L.

LONE WOLF DIST.

ULTIMATE ARMORER’S TOOL for GLOCK®

Just One Tool For Complete Maintenance,

Disassembly

#100-000-774AS Ultimate Armorer’s Tool, 2K19K81 � � � �$ 20.99

Stainless steel tool is precisely machined to hold the Glock channel liner securely dur-ing removal and installation. Unique double-headed design has threaded end for removal and smooth end for installation. Makes a delicate job quick and easy while preventing damage to slide and liner that can occur when using makeshift tools. abSPECS: Stainless steel. 43/4" length. Instructions included.

JENTRA

CHANNEL LINER TOOL FOR GLOCK®

The Correct Tool For Removal & Installation

#463-000-009AS Channel Liner Tool, 3F21B95 � � � � � � � � �$ 21.95

The same tool used at the Glock Factory to ac-curately remove and install the firing pin channel liner.

The disposable liner must be removed, and a new one installed, when rebluing or refinishing. Easy-to-use tool will not damage or mark the slide. Includes complete instructions, plus one channel liner. abSPECS: Steel, blue. 6" (15cm) long. Fits all models of Glock pistols.

RIMFIRE GUN WORKS

CHANNEL LINER TOOL for GLOCK®

Removes & Installs Liners Without Slide Damage

#777-100-017AS Channel Liner Tool for Glock, 7G27J99 � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 27.99

Solid, high-strength vise block holds Glock pistols securely for easy cleaning and maintenance. Keeps both hands free for de-tailed, precision work and helps eliminate the chance of dropping the pistol and causing damage. Slides into the mag well and locks tight using the factory latch without marring or scratching. Durable, polymer composite construction is resistant to most solvents. Fits all 9mm and .40 cal. Glock pistols. abSPECS: Polymer, black. Stem - 41/4" (10.8cm) long x 11/4" (3.2cm) wide.

C.B. GIORNESTO

THE GLOK BLOK for GLOCK®

Holds Pistol Securely For Easy Cleaning & Maintenance Using Both Hands

#100-003-691AS Glok Blok, 6B34M63 � � � � � � � � � � � � � � � �$ 39.95

Plastic tool engages Glock slide lock and provides mechanical ad-vantage to ease slide removal. Fits all Glock models with standard and

extended slide locks. Texture lines provide plenty of purchase for thumb and finger, while the bright yellow color makes this tool easy to find in your toolbox or on your bench. abSPECS: Plastic, yellow.

GTUL

SLIDE REMOVAL TOOL for GLOCK®

Makes It Easy To Remove Glock Slide

#100-011-518AS Slide Removal Tool for Glock, 2C10M59 � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 11.95

Steel tool is specially shaped to fit beneath the pin recess of Ruger LCP slide stop for simple removal, letting you clean the gun or perform maintenance. Makes process fast and easy compared to using your fingertips. Durable plastic handle gives long service life and is specially contoured to aid grip. abSPECS: 1018 steel, black oxide finish.

RUGER® LCP

SLIDE STOP PIN REMOVAL TOOLEases Slide Stop Pin Removal

On Popular Carry Pistol

#080-001-093AS Brownells Ruger LCP Slide Stop Pin Tool, 8K12C89 � � � � � � � � � � � � � � � � � � � � � $ 15.99

We redesigned our original Replaceable Pin Punch to create the perfect length and size for driving roll pins on S&W M&P pistols. The handle features a removable knurled chuck to hold the bevel-head-ed punch pin, as well as checkering on the body to ensure a solid grip. Small center nub on the end of the punch seats into roll pins and helps prevent slipping and damaging your firearm. Punch tip is made of tool steel and hardened to Rc 54-58 for increased durabil-ity, with replacement pins available if original is bent or broken. abSPECS: Steel. Handle - 3" (7.6cm) long x 3/8" (.95cm) diameter. Pin – 1.5" (3.8cm) long x .122" (.3cm) diameter.

/APEX TACTICAL S&W M&P

HEAVY DUTY PIN PUNCHSpecifically Designed

For Removing M&P Series Roll Pins

#080-001-103AS Heavy Duty Pin Punch, 8K8G46 � � � � � � $ 9.99#080-001-101AS Replacement Pin, 8K4P15 � � � � � � � � � � � 4.99

Multi-use tool with large, easy-to- grasp han-dle performs several maintenance and repair tasks. Removes grip screws, mainspring assembly; provides controlled removal of main-spring. Installs and removes sear spring and magazine catch. Handy to have on the bench, indispensable for emergencies in the field.SPECS: Plastic handle, steel shank. Approximately 71/2" (19cm) long. Four interchangeable bits. Fits 220, 225, 226, 228, 229, 230, 232. 239, 245.

SIG SAUER COMBO TOOLHandy Tool For Bench Or

Field Use

#719-100-000AS SIG Combo Tool, 9A42C35 � � � � � � � � � $ 44.99

Small, self-contained, takedown tool has everything you need to field strip your Ruger Mark I or II pistol. The tool’s aluminum end cap has a steel, wire loop for removing the main-spring housing latch. Punch on op-

posite end drives out the bolt stop pin without marring the metal. Unscrew end cap to expose a pin for removing the extractor, plunger and spring for cleaning or replacement. abSPECS: Body/Punch - Delrin, black. Extractor Tool - Aluminum/steel. 37/8

" (cm) OAL, 1/2

" (1.3cm) diameter.

GUNSMITHER TOOLS RUGER® MARK I/II

TAKEDOWN TOOLDisassemble Your .22 Auto

Fast & Easily

#100-001-507AS Ruger MKI/MKII Takedown Tool, 7A12G45 � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 13.95

Made of heavy duty delrin, this multipurpose tool makes the disassembly and reassem-bly of Ruger rimfire pistols quick and easy. Assists in removing the mainspring housing, bolt and recoil spring, and removing the upper receiver from the frame. When it’s time for reassembly, the tool helps get the recoil spring back on the bolt, ensure the internal mechanisms are aligned before insertion of the bolt, plus it gives you the proper grip and pressure needed to get the mainspring housing pin back into the gun. Tool can even be used to push down the fol-lower button when loading the magazine. Tool available alone or with a durable cardboard stand that provides a stable platform to hold the pistol and free up your second hand. ab

THE RIGHT TOOL CO. RUGER® MARK I/II/III & 22/45

ALL-IN-ONE TOOLMakes Cleaning Your Pistol

Hassle Free

#100-015-788AS All-In-One Tool, 4R20J69 � � � � � � � � � � �$ 21.95#100-015-789AS All-In-One Tool & Stand , 4R26D53 � � � 27.95

Ultra-compact, pocket tool makes disassembly of Sig Sauer pistols fast and easy. Use to re-move or install grip screws, maga-zine catch and support plate, pivot pins, sear and deco*cker springs, and the mainspring assembly on

both current-production and older pistols. Also aids in disassem-bling magazines for cleaning and maintenance. Strong internal magnets retain the replaceable (1/4" hex drive) screwdriver bit and help keep small parts from rolling away during disassembly. abSPECS: Body – 6061 T6 aluminum, hardcoat anodized, matte black. Driver Bit & Disassembly Pin Punch – stainless steel. 21/2" (6.35cm) long, 1/2" (1.27cm) wide, 3/4" (1.9cm) high. 1.6 oz. (45g) weight. For Sig Sauer P220, P225, P226, P228, P239, and P245 DA/SA models. Instructions included.

SIG SAUER PISTOL SPD TOOLFor Fast, Easy Field-Stripping Of Sig Pistols; Fits In Pocket

#080-000-721AS SPD Tool, 1B45H93 � � � � � � � � � � � � � � � � $ 49.99

This hardened steel punch is designed to aid in the removal of the extractor pin and the firing pin positioning pin found in the SIG E2 slides. The half-round

profile gives maximum contact area on the partially exposed ends of the pins and transfers the hammer blow efficiently. A built-in stop limits tool travel to the proper depth to avoid marring the slide. abSPECS: S7 hardened tool steel, black oxide finish. Length – 3½"; tip diame-ter - .118" (3mm), body diameter - .320" (8mm). Fits SIG P226E2 & P229E2.

K & C BARRELS SIG SAUER®

E2 SLIDE DISASSEMBLY TOOLThe Correct Tool For The

New E2 Slides

#100-009-923AS SIG SAUER E2 Slide Tool, 5B17P63 � � � �$ 19.99

Compact, two-in-one specialty tool removes the firing pin spring pin, plus the hammer mainsprings on your P250 pistol. Features an elliptical tip for push-ing on the firing pin spring pin without flattening the head, plus a concave tip for the safe, controlled removal of the hammer double mainsprings. Precision machined from steel bar stock, then hard-ened to Rc 52 for added strength. Small enough to fit in your pocket, range bag, or armorer’s kit. abSPECS: Steel, Rc 52 hardness. 31/2" (9.5cm) long x 5/16" (8mm) diameter handle.

K AND C BARRELS SIG SAUER P250

ASSEMBLY & DISASSEMBLY TOOLRemoves Firing Pin

Spring Pin & Hammer Mainsprings

#100-004-424AS Assembly & Disassembly Tool, 5B17P47 � � � � � � � � � � � � � � � � � � � � � � � � � � � �$ 19.99

60°- STANDARD SLOTSpecially manufactured, true parallel, 3-square file with only one

side cutting - other two sides “safe”. This means the file can be used to widen dovetail slots in gun barrels without danger of deepening the slot or damaging the edge not being worked on. Being a true parallel file, you have absolute control over the angle of the dovetail - impossible with other type files. SPECS: 7" (17.8cm) long. .284" (7.2mm) wide. #1, medium, doublecut. #2, fine, single-cut.#080-648-160AS #1 60° Sight Base File, 6C42K85 � � � � � $ 49.99#080-648-060AS #2 60° Sight Base File, 8K41M74 � � � � � 46.99

65°- 1911 AUTO-TYPE SLOTDesigned especially for widening and final fitting after using our

65° Sight Base Cutter to cut the basic slot. Or, can open up a 60° slot to proper 65° angle if changing to a new sight design. Has true parallel cutting edges for precision filing, giving you full control over the angle of the dovetail. One cutting side only, with the other two sides “safe”, so you can widen or deepen sight slots safely without fear of changing the other dimensions. SPECS: 7" (17.8cm) long. 3/16" (4.8mm) wide. #1, medium, doublecut. #2, fine, single-cut.#080-648-165AS #1 65° Sight Base File, 6C32H90 � � � � $ 34.99#080-648-265AS #2 65° Sight Base File, 6C36F29 � � � � � 39.99

(See Sight Base Cutters listed elsewhere.)

SIGHT BASE FILES

The Professional Way To Safely Widen Or Cut New Dovetails

PAGE 483Orders/Tech: 800-741-0015order on the web

brownells.com

SPE

CIA

LTY

N T

LS SIGHT BASE CUTTERS

CUSTOM MADE DOVETAIL END MILLS IN BOTH PREMIUM CARBIDE AND HIGH SPEED STEEL

#080-621-060AS Carbide Standard Sight Base Cutter, 8K73D54 � � � � � � � � � � � � � � � � � � � � � � � � � � �$ 79.99

SPECIAL FRONT SIGHT DOVETAIL CUTTERSUnique Sizes For Wilson & Meprolight

WILSON SNAG-FREE DOVETAIL CUTTER - Cuts the .290" x 60° dovetail required to install all current models of the Wilson Snag-Free front sights. CAUTION: For use in milling machine only.

HIGH-SPEED STEEL WILSON DOVETAIL CUTTER - 2" (5cm) long. .375" (9.5mm) diameter shaft. 60° shoulder. DO NOT EXCEED 700 rpm, HIGHER SPEED WILL BREAK TEETH. ab#080-621-290AS Wilson Dovetail Cutter, 8K29K97 � � � � �$ 36.99

CARBIDE WILSON DOVETAIL CUTTER - Solid carbide 2" (5cm) long. .375" (9.5mm) diameter shaft. 60° shoulder. ab#080-621-291AS Carbide Wilson Dovetail Cutter,

7A60J44 � � � � � � � � � � � � � � � � � � � � � � � � � � �$ 79.99

MEPROLIGHT® DOVETAIL CUTTER - Cuts the .250" x 74° dove-tail required when altering ramp-style front sights to accept Mep-rolight’s Universal front sight inserts. Cutter can be used to open up a standard ramp when installing Brownells Colored Sight Inserts. DO NOT EXCEED 700 RPM. HIGHER SPEED WILL BREAK TEETH. ab#080-621-250AS Dovetail Cutter, .250" x 74°,

8K38J45 � � � � � � � � � � � � � � � � � � � � � � � � � � $ 44.99

HSS SEMI-AUTO PISTOL SIGHT BASE CUTTER - High speed steel, 2" (5cm) long, 3/8" (9.5mm) diameter shank. 60° or 65° shoulder. DO NOT EXCEED 700 rpm, HIGHER SPEED WILL BREAK TEETH. ab #080-621-331AS 60° HSS Semi-Auto Sight Base Cutter,

8K31P71 � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 36.99#080-621-330AS 65° HSS Semi-Auto Sight Base Cutter,

8K25B91� � � � � � � � � � � � � � � � � � � � � � � � � � � 31.99

CARBIDE SEMI-AUTO PISTOL SIGHT BASE CUTTER - Solid car-bide cutter resists wear when cutting pistols made from hardened steel. 2" (5cm) long, 3/8" (9.5mm) diameter shank. 60° or 65° shoul-der. ab#080-621-066AS 60° Carbide Semi-Auto Sight Base

Cutter, 7A65J72 � � � � � � � � � � � � � � � � � � � �$ 85.99#080-621-065AS 65° Carbide Semi-Auto Sight Base

Cutter, 8K75A00 � � � � � � � � � � � � � � � � � � � � 89.99

FRONT SIGHT INSERT CUTTER

60° Shoulder x .245"

We’ve had many requests for a small dovetail cutter that would speed up the cutting of dovetails in front sight blades when installing colored inserts. The one we’ve had made cuts a ¼" wide dovetail, just right for sight inserts, and the finished product is very precise. Since the cutter is small, (it tapers to a diameter of .110"), you must make an initial cut with a 1/8" end mill (listed below). By using the end mill to remove some metal first, you’ll avoid overloading the cutter and breaking it. CAUTION: For use in milling machine only.

HSS FRONT SIGHT INSERT CUTTER - High speed steel. 21/32" (5.1cm) long. ¼" (6.3cm) diameter shank. Maximum cut depth is .100" (2.5mm) 60° shoulder. DO NOT EXCEED 700 rpm, HIGHER SPEED WILL BREAK TEETH. ab#080-621-245AS HSS Front Sight Insert Cutter,

8K24N07 � � � � � � � � � � � � � � � � � � � � � � � � � � $ 29.99

CARBIDE SIGHT INSERT CUTTER - Solid carbide 2" (5cm) long. ¼" (6.3cm) diameter shank. 60° shoulder. ab#080-621-246AS Carbide Sight Insert Cutter,

7A54B73 � � � � � � � � � � � � � � � � � � � � � � � � � � � �$ 71.99

HEINIE REAR SIGHT CUTTER

65° Shoulder x .370"

Cuts the .370 x 65° dovetail required when fitting Heinie rear sights. Solid carbide cuts the hardest slides with minimal wear. ab #080-621-371AS Carbide Heinie Rear Sight Cutter,

7A58M56 � � � � � � � � � � � � � � � � � � � � � � � � � � �$ 70.99

STANDARD SIGHT BASE CUTTER

60° Shoulder x .359"

Universal Sight Base Cutter made for sights with 60° shoulder and a 3/8" base. Cuts most standard front and rear rifle sights as well as 1911 Auto low-mount, adjustable sights like E.E.A. Super Sights, Millett and Bo-Mar-style. Cutter is slightly undersized at .359" which requires that you make two cutting passes to compensate for facto-ry variations in sight manufacture and milling tolerances. Designed with proper relief for maximum strength and clean cutting. CAU-TION: For use in milling machine only.

HIGH SPEED STEEL STANDARD SIGHT BASE CUTTER - 2" (5cm) long. 3/8" (9.5mm) diameter shank. 60° shoulder. DO NOT EXCEED 700 rpm, HIGHER SPEED WILL BREAK TEETH. ab#080-621-359AS HSS Standard Sight Base Cutter,

8K29Q57 � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 37.99

CARBIDE STANDARD SIGHT BASE CUTTER - Solid carbide. 2" (5cm) long. 3/8" (9.5mm) diameter shank. 60° shoulder. ab

LOW MOUNT 1911 AUTO SIGHT BASE CUTTER

65° Shoulder x .495"

These cutters are specially designed by us and made to our specifications for cutting the sight base slot required to mount the Wichita and Novak Lo-Mount 1911 Auto sights. Use ¼" carbide end mill to remove the bulk of the material (see drawing above) then make final dovetail cut. Final cut to lower rear of slide is done with an end mill and is not a part of the sight base cut. Made slightly undersized to compensate for variations in sight bases and milling tolerances on installation. With the popularity of custom 1911 Auto pistols, this cutter is one that you will use frequently in your custom work. CAUTION: For use in milling machine only. ab

HSS DOVETAIL SIGHT BASE CUTTER - 2" (5cm). .495" diameter cut. ½" (12.7mm) diameter shank. 65° shoulder. DO NOT EXCEED 700 rpm, HIGHER SPEED WILL BREAK TEETH. #080-621-495AS HSS Lo-Mount Sight Base Cutter,

8K44M84 � � � � � � � � � � � � � � � � � � � � � � � � � � �$ 52.99

CARBIDE DOVETAIL SIGHT BASE CUTTER - Much harder and lon-ger-lasting than HSS cutter. Use on hardened Colt factory slides. Solid carbide, 2" (5cm) long. .495" diameter cut. ½" (12.7mm) di-ameter shank. 65° shoulder. #080-621-965AS Carbide Lo-Mount Sight Base Cutter,

9K96D43 � � � � � � � � � � � � � � � � � � � � � � � � � $ 114.99

FRONT SIGHT DOVETAIL CUTTER

60° & 65° Shoulder x .300"

Cuts lengthwise dovetail required to install special handgun front sights from Jim Clark, Ed Brown, Bob Marvel and others. Slight-ly undersized to allow for precise final fitting and to compensate for any machine wear. CAUTION: For use in milling machine only.

HSS FRONT SIGHT DOVETAIL CUTTER - High speed steel. .300" (7.3mm) diameter cut, 3/8" (9.5mm) diameter shank. 60° or 65° shoulder. DO NOT EXCEED 700 rpm, HIGHER SPEED WILL BREAK TEETH. ab#080-621-300AS 60° HSS Front Sight Dovetail Cutter,

8K34F76 � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 44.99#080-621-305AS 65° HSS Front Sight Dovetail Cutter,

8K30J45 � � � � � � � � � � � � � � � � � � � � � � � � � � 36.99

CARBIDE FRONT SIGHT DOVETAIL CUTTER - Solid carbide resists wear and easily cuts through even hardened steels. .300" (7.3mm) dia. cut, 3/8" (9.5mm) dia. shank. 60° or 65° shoulder. ab#080-621-960AS 60° Carbide Front Sight Dovetail

Cutter, 7A64G44 � � � � � � � � � � � � � � � � � � � � $ 77.99#080-621-963AS 65° Carbide Front Sight Dovetail

Cutter, 7A63N04 � � � � � � � � � � � � � � � � � � � � 80.99

SEMI-AUTO PISTOL SIGHT BASE CUTTER

60° & 65° Shoulder x .330"

Our special 65° shoulder Sight Base Cutter designed to cut dovetails for both standard Colt factory and mil-spec 1911 Autos, and for replacement sights like Wichita Hi-Mount, older Bo- Mar and others with a 65° shoulder. Some makers use a 60° dovetail on their rear sights and we also have a cutter to match them. For low-mount adjustable sights use the Standard Sight Base Cutter shown on this page. Actual cutting diameter is .330" so more than one pass will be required to install most sights. This is done on purpose to allow for factory variations in base width as well as milling tolerances. CAU-TION: For use in milling machine only.

Handy tool slides between the extractor and frame to easily lift out the extractor on your XD/XDM pis-

tol. Tool is ideal when you need to replace a broken extractor or want to give your pistol a thorough cleaning. abSPECS: Steel.

PISTOLGEAR SPRINGFIELD XD/XDM

EXTRACTOR REMOVAL TOOLMakes Removing The Extractor

Quick & Easy

#100-015-784AS XD Extractor Removal Tool, 4G11L95 � $ 11.95

These punches are spe-cifically designed for the installation, removal, and adjustment of front and rear handgun sights. Made of brass so they will not mar the sight or the gun if you slip. Unique triangular punch faces and heavy-duty bodies make them indispensable working tools for the gunsmith. Can be re-ground to square up the flat after multiple uses. Front Sight Punch has a base width of approximately .280"; Rear Sight Punch has a base width of approximately 0.480". They are sold separately or can be purchased together in a handy Kit. The Small Dovetail Sight Punch (sold separately) has a .230" base width, making it ideal for front and rear sights on compact handguns. abSPECS: Brass. Approx. 3½" OAL, with 1" punch tip.

DOVETAIL SIGHT PUNCHESNon-Marring Brass Punches Purpose-Designed For Sight

Work

#080-001-138AS Front Sight Punch, .280", 8K8A57 � � � � � $ 9.99#080-001-139AS Rear Sight Punch, .480", 8K10P61 � � � � � 11.99#080-001-164AS Front/Rear Sight Punch Kit,

8K19K29 � � � � � � � � � � � � � � � � � � � � � � � � � � � 21.99#080-001-230AS Small Dovetail Sight Punch, .230",

8K8Q57 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 9.99

Specifically designed to install, adjust and remove all models of Trijicon Glock Sights without dam-age. Includes heavy-duty rear sight mover with oilite bushings that al-low for very fine windage adjustments, and a front sight nut driver that fits all models of aftermarket front sights. abSPECS: Aluminum, anodized finish. 3/16" nut driver.

TRIJICON® SIGHT INSTALLATION TOOL for GLOCK®

Install, Adjust & Remove Glock Sights Without Damage

#892-103-102AS Glock Sight Install Tool, 2H139E99 � $ 139.99

Safely moves fixed sights right or left in their dovetails without de-forming slide or sight. Specifically designed for use with factory and aftermarket Tritium night sights, which are too fragile for the tradi-tional hammer-and-punch sight installation method; works equally well with iron sights. Thumbscrew

securely locks the slide so it's fully supported in the rigid, machined aluminum body. Separate slots in the screw mechanism engage the sight and firmly, yet gently, concentrate screw force to loosen sights from even extremely tight dovetails. Hardened steel handle provides plenty of leverage, while self-lubricating, oil-impregnated Oilite® bronze bearings and extra-fine threads ensure smooth, pre-cise movement. Beretta/Glock models fit rear sights only. Glock Flat-Side fits aftermarket rear sights with straight, non-sloped sides for standard- and large-frame Glock pistols. Glock 42/43 Adapter re-quired to adjust sights of G42 and G43 pistols in either Glock Sight Mover. SIG fits rear sights on all SIGs except SIG-PRO. Smith & Wes-son M&P fits both front and rear sights; will not fit Pro models with 5" barrel. Springfield XD fits both front and rear sights on all XD models except front sight on 5" barrel Tactical model. abSPECS: Aluminum body, anodized. Steel cross carriage bolt and thumb-screw, black oxide finish. Approx. 43/4" (12.1cm) wide x 3" (7.6cm) high x 1" (2.5cm) thick. Exact size varies from model to model.

MGW SEMI-AUTO

SIGHT MOVERAdjusts, Removes & Installs

Sights Without Damage

#584-045-092AS Beretta 92 Sight Mover, 4H99B91 � � � $ 116.99#584-045-093AS Beretta 8000/Cougar Sight Mover,

4H99K91 � � � � � � � � � � � � � � � � � � � � � � � � � � 116.99#584-045-017AS Glock Sight Mover, 4H97J85 � � � � � � � � 99.99#584-000-004AS Glock Flat-Side Sight Mover,

4H99I91 � � � � � � � � � � � � � � � � � � � � � � � � � � � 116.99 584-042-043AS Glock 42/43 Adapter, 4H30K80 � � � � � 33.99#584-045-220AS SIG Sight Mover, 4H117N88 � � � � � � � � � 129.99#584-000-003AS S&W M&P Sight Mover, 4H120F16 � � � 124.99#584-045-002AS S&W M&P Shield Sight Mover,

4H117B78 � � � � � � � � � � � � � � � � � � � � � � � � � 124.99#584-000-002AS Springfield XD Sight Mover,

4H122L13 � � � � � � � � � � � � � � � � � � � � � � � � � � 139.99

Item

PAGE 484 Office/Tech: 641-623-5401SATISFACTION GUARANTEED

SINCE 1939

SPE

CIA

LTY

N T

We’ve taken our most popular dovetail cutters and cryogenically treated them to give you a tool that will cut the toughest material and last longer, saving down-time and increasing your production. Our cryo-treated tools have been deep-treated to -320°F to change the molecular structure of the metal alloy, making them denser and removing the stresses that lead to tool fatigue. Cryo-treated tools do not look different than untreated tools, so we’ve added two rings near the working end to differentiate them from our regular cut-ters. abSPECS: Cryo-treated, high-speed steel.

CRYO-TREATED DOVETAIL CUTTERLonger Cutting Life;

Reduces Replacement Costs

STOCK # SIZE PRICE#080-000-271AS 60° x .245" 8K32L19 $ 39.97#080-000-272AS 74° x .250" 8K46B12 $ 59.25#080-000-273AS 60° x .290" 8K34M94 $ 41.46#080-000-274AS 60° x .300" 8K43B32 $ 54.46#080-000-275AS 65° x .330" 8K33C82 $ 41.50#080-000-276AS 60° x .330" 8K40N68 $ 46.99#080-000-277AS 60° x .359" 8K37D40 $ 45.99#080-000-278AS 65° x .490" 8K43D08 $ 52.99#080-000-279AS 65° x .300" 8K39E53 $ 45.99

Precision CNC machined tool safely removes, installs and adjusts fragile Tritium, front and rear night sights on H&K USP and P2000 pistols. Easy-to-use, just place your pistol slide in the tool, making sure the sight dovetail lines-up with the sight pusher, then turn the adjustment knob to clamp the slide in place. Turn the easy-to-grasp, hardened steel T-handle to slowly press the pusher tip against the sight and gently push the sight into the dovetail. Self-lubricating, oil-impregnated Oilite® bronze bearings and extra-fine threads help ensure smooth, precise sight adjustment. Specifically designed for use with fixed, front and rear, dovetailed Tritium night sights. abSPECS: 6061 T6 Aluminum, anodized, red. Steel lead screw and adjust-ment knob, black matte finish. Body - 43/4" (21cm) long x 15/8" (1.9cm) wide. Fits factory and aftermarket, fixed front and rear sights on all full size & compact HK USP and P2000 pistols.

AMERIGLO H&K USP/P2000

SIGHT ADJUSTMENT TOOLRemoves, Installs & Adjusts

Dovetail Sights Without Damage

#100-004-195AS Sight Adjustment Tool, 4K127L58 � � � $ 133.99

Handy kit has ev-erything you need to

professionally install, remove, or adjust sights on Glock pistols – including a set of Trijicon night sights for your first job. The hefty, gunsmith-grade MGW Rear Sight Mover tool works on any Glock pistol with angle-sided rear sights. The B&J Machine combina-tion tool is one of the best we’ve found for working on Glock front sights. The kit’s Trijicon Bright & Tough™ front/rear night sights fit any 9mm/.40 S&W Glock and give your pistol a classic 3-dot sight picture that’s visible in all lighting conditions. abSPECS: MGW Rear Sight Mover – aluminum and steel construction. B&J Tool – Delrin® handle, steel punch and wrench. Sights – Steel, blued with tritium inserts. Fits Glock 17/17L/19/22/23/24/26/27/33/34/35 pistols with fixed sights.

SIGHT INSTALLATION STARTER KIT for GLOCK®

Gunsmith Tools To Work On Glock Sights – Plus A Set Of Night

Sights

#080-000-935AS Sight Installation Starter Kit for Glock, 9Z212K04 � � � � � � � � � � � � � � � � � $ 219.99

Universal sight installation tool al-lows you to change or adjust iron sights on a variety of pistols. Tool has two primary components: the

upper carriage which includes the pusher assembly, and the lower slide support assembly. Carriage features a Delrin® pad set exactly .015" above the slide, removing any guess work about how high to set pusher assembly. Pad is adjustable for pistols which have a raised sight platform. Four slide support pads, two top clamping bolts and four side bolts ensure the slide is secure and straight. Tool comes with straight sided pusher assembly which fits most pistols. Durable tool will withstand years of use. Features machined notches for vise mounting or can be used as a hand tool. Tool comes with instructional DVD. Interchangeable Slide Shoe Clamps are firearm specific, giving you a wide range of versatility to the pistols you work on. Shoes are made from low carbon steel with a black oxide finish, and are sold separately below. ab

MGW

SIGHT PRO TOOL

One Tool Lets You Install Sights On A Variety Of Pistols

Main Sight Tool

STOCK # FITS PRICE#584-000-016AS Beretta 92 4H17K51 $ 17.99#584-000-017AS Beretta Cougar/PX4 4H17N51 $ 17.99#584-000-036AS Bersa BP Series 4H17K51 $ 17.99#584-000-029AS Browning Hi-Power 4H17C51 $ 17.99#584-000-010AS Colt 1911 4H17N51 $ 17.99#584-000-023AS Colt Mustang .380 4H17L51 $ 17.99#584-000-026AS CZ-75 4H17N51 $ 17.99#584-000-013AS FN FNP/FNS/FNX/Forty-Nine

9mm/.404H17L51 $ 17.99

#584-000-034AS FN .45 ACP Pistol 4H17M51 $ 17.99#584-000-007AS Glock, all (except Glock 42) 4H17N51 $ 17.99#584-000-020AS Glock 42 4H17E51 $ 17.99 584-000-045AS Grand Power P11 MK12 4H17I34 $ 17.99 584-000-043AS H&K VP9 4H17E51 $ 17.99#584-000-035AS Kahr P40/C240/PM9 4H17C51 $ 17.99 584-000-042AS Kahr P45 4H17J51 $ 17.99#584-000-024AS Ruger LC Series 4H17D51 $ 17.99#584-000-038AS Kimber Solo Carry 4H17G51 $ 17.99#584-000-025AS Ruger P-Series 4H17K51 $ 17.99#584-000-022AS Ruger SR Series 4H17C51 $ 17.99#584-000-014AS Sig P220/225/239/226/228/229

Slide4H17N51 $ 17.99

584-000-041AS Sig P224 4H17F51 $ 17.99#584-000-027AS Sig P238 4H17F51 $ 17.99 584-000-044AS Sig P290 4H17L51 $ 17.99#584-000-040AS Sig P320 4H17D51 $ 17.99#584-000-028AS Sig P938 4H17P51 $ 17.99#584-000-015AS Sig Pro Series 4H17I51 $ 17.99#584-000-012AS S&W 3rd Gen 9mm 4H17J51 $ 17.99#584-000-032AS S&W 3rd Gen .45 ACP 4H17B51 $ 17.99#584-000-019AS S&W M&P (all except Shield) 4H17A51 $ 17.99#584-000-009AS S&W M&P Shield 4H17I51 $ 17.99#584-000-030AS S&W .380 Bodyguard 4H17B51 $ 17.99#584-000-031AS S&W Sigma 4H17D51 $ 17.99#584-000-011AS Springfield XD (all except XD-S) 4H17J51 $ 17.99#584-000-008AS Springfield XD-S 4H17N51 $ 17.99#584-000-037AS Steyer M40/MPS/M9-A1 4H17E51 $ 17.99#584-000-018AS USP/P2000/P45 4H17H51 $ 17.99#584-000-039AS Walther P99 4H17C51 $ 17.99

Items

Universal bench tool provides accurate cross-dovetail pistol sight adjustment and installation without damage to the sight or the slide. Multi-position, slide support block and separate slide clamp adjust quickly. Body is machined from a solid block of aluminum alloy. Square thread adjustment screw provides plenty of leverage to move even the most stubborn sight without damage. Includes attachment ears for bench mounting.SPECS: Body - Aluminum, black, hardcoat anodized finish. 6" (15cm) wide, 41/2" (11cm) high, 2 lb. (.9kg) wt. Adjustment Screw - Hardened steel. In-cludes complete instructions and pistol sight reference chart. Will not install tenon-style front sights.

MEPROLIGHT® UNIVERSAL SIGHT INSTALLATION TOOL

Adjust & Install Over Forty Different Semi-Auto Pistol

Sights

#387-100-000AS Type II Univ. Sight Tool, 2B679C99 � �$ 679.99

Prec is ion-machined , steel tool safely removes, installs and adjusts front and rear sights on handguns.

Clamp your slide into the tool and line up the sights with the tool’s pusher tip for installation, removal, or adjustment. Mobile jaw cus-tomizes to the height of your slide and can be used from the right or left side. Delrin® liner protects slide from scratches. Includes three sight pushers that attach to the end of the sight-pushing bolt. 1/4" square tip works perfectly on shallow, cross-dovetail sights. Hold Down Clamp helps prevent the slide from twisting in the frame of the P500 by applying extra force to the top of the slide. Provides a secure seat in the tool when working with hard-to-remove sights or slides with angled sides, like the Springfield Armory XD and the S&W M&P. Slide Stop speeds up the process of performing the same sight job on a large number of the same model pistol. Stop simply screws to the P500 frame and lets you position each slide in exactly the same place to perform the necessary sight adjustment quickly and easily. P500 Universal Sight Tool Kit combines P500 Universal Sight Tool with the Hold Down Clamp and Slide Stop to provide the ultimate of flexibility and versatility in a sight adjustment tool. abSPECS: Steel, black, powder-coat finish. Approximately 5" (12.5cm) long, 2" (5cm) wide, 1" (2.54cm) high. Instructions included. Hold Down Clamp – Steel, powder-coated, black. Approximately 4" (10cm) long, 1½" (3.8cm) wide, 3¾" (9.5cm) high). Comes with clamp assembly, jaw screw, 3/32" hex wrench, and instructions. Slide Stop - 1018 steel, black oxide finish. Ap-proximately 1¼" (3.2cm) long, ½" (1.3cm) wide, 1" (2.5cm) high. Includes stop block, stop pin, hex wrench, (5) 6-32 setscrews, and instructions. P500 Universal Sight Tool Kit contains the P500 Universal Sight Tool, Hold Down Clamp, Slide Stop, and complete instructions.

B&J MACHINE

P500 UNIVERSAL SIGHT TOOLSafely Removes & Installs

Dovetail Front & Rear Sights; Works On Shallow,

Cross-Dovetails

#694-000-001AS P500 Sight Removal Tool, 4F133C06 � � $ 139.99#694-000-003AS Hold Down Clamp, 4F62L69 � � � � � � � � 64.99#694-000-002AS Slide Stop, 4F22K39 � � � � � � � � � � � � � � � � 24.99#694-000-004AS P500 Universal Sight Tool Kit,

4F215D99 � � � � � � � � � � � � � � � � � � � � � � � � � 215.99

The P500 Pro builds on the original P500 sight pusher by incorporating a hold down clamp and slide positioning stop into the design and using rede-signed pushers to minimize flex and increase the strength of the tool. The pusher and hold down mechanisms are fully adjustable and can be positioned to accommodate almost any slide securely for delicate sight installations. The built-in positioning stop allows the same slide to be removed and quickly replaced while maintain-ing proper alignment as many times as needed to adjust the sight - an especially handy feature for LE qualifications or any time multiple pistols of the same model require sight work. The tool is made from steel for strength and features polymer clamping surfaces to protect the gun’s finish. abSPECS: Steel, black finish. Approximately 5½" (13.97cm) long, 4" (10.2cm) wide, 3½" (8.9cm) high.

B&J MACHINE

P500 PRO UNIVERSAL SIGHT TOOLImproved Tool For Installing

& Removing Auto Pistol Sights

#694-000-005AS P500 Pro Sight Tool, 4F274P99� � � � � �$ 274.99

Designed for installing or re-moving the hex nut on Glock front sights, this nickel-plated, steel driver also fits S&W Sigma, Walther, and

other brands with a 3/16" hex sight nut. Compact size (only 1.6" long) fits easily in a small tool kit, range bag, or your pocket. Knurled top gives you a positive grip for popping loose tight sight screws. ab

GLOCK®

FRONT SIGHT TOOLSimple Tool Easily Pops Loose Tight Front Sight Hex Screws

#080-001-092AS Glock Front Sight Tool , 8K5H46 � � � � � � $ 7.99

Fits the small, hex head screw that holds Glock sights in place. Makes installing replace-ment sights or removing sights

for maintenance easier with less chance of damage. Hex shank fits Magna-Tip® screwdrivers. Not for use with 6" slides. All-steel construction. ab

ED BROWN

FRONT SIGHT TOOL for GLOCK®

Easily Removes/Installs Glock Front Sights

#087-017-001AS Glock Front Sight Tool, 7H17C87 � � � � �$ 19.95

Leave your comments or suggestions!

PAGE 485Orders/Tech: 800-741-0015order on the web

brownells.com

SPE

CIA

LTY

N T

Here it is! A tool kit designed specifically for the armorer, gunsmith, shop, or depart-ment servicing Smith and Wesson Revolvers. You get everything needed to perform

virtually any internal repair or rebuilding chore on the innumerable Smiths found in police departments and law enforcement agencies throughout the U.S. and the world. To put together this kit, filled with many one-of-a-kind tools, we drew on the knowledge of many good friends (to whom we are forever indebted) who work on these guns every day. Special Thanks to Gene Thompson, Brunswick, Georgia who not only pushed us hard to put the kit together but also lent us many of his personal tools to use as patterns. What you get is a 41-piece kit of first quality, professional tools to help you service Smiths faster, more efficiently and without the errors often caused by “pick-up” or “make-do” equipment. Although designed primarily for the “K” frame, many of the tools work on other Smith frame sizes and other makes of revolvers too. ab

⑮ ARMORER’S BRUSH - Perfect for dusting recesses.#821-135-210AS Armorer’s Brush, 8K7N65 � � � � � � � � � � � � $ 8.99

⑯ BROWNELLS ASSEMBLY/DISASSEMBLY MAT - Provides no-slip, no-scratch work surface anywhere.#358-128-316AS Assy/Disassy Mat, 8E20L55 � � � � � � � � � $ 22.99

⑰ HAND & CYLINDER STOP WINDOW FILES - Correct offset shapes and sizes to alter these openings for new parts.#080-754-000AS Hand Window File, 6C31N78 � � � � � � � � $ 36.99#360-318-731AS Cylinder Stop Window File,

6C30F99 � � � � � � � � � � � � � � � � � � � � � � � � � � 30.99

⑱ #455 CENTER PUNCH - Swages hammer nose rivet.#587-113-455AS Center Punch 455, 7H4H55 � � � � � � � � � � �$ 4.55

⑲ GUN/PARTS CLEANING BRUSH#676-450-001AS Gun/Parts Brush, each, 8K1B40 � � � � � � �$ 3.99

⑳ BROWNELLS REBOUND SLIDE SPRING TOOL - Clears the frame and compresses the rebound spring.#080-666-000AS Rebound Slide Tool, 3K15H88 � � � � � � � �$ 19.99

◯21 LAW ENFORCEMENT MAGNA-TIP® S&W SCREWDRIVER COMBO - Clip-tip handle with three bits for S&W screws.#080-088-003AS S&W Screwdriver Set, 8K15J35 � � � � � � �$ 16.99

◯22 60/68 HEADSPACE GAUGE - Fast and accurate check.#080-633-668AS 60/68 Cylinder Gauge, 8K30K06 � � � � �$ 35.99

◯23 38 BARREL ALIGNMENT GAUGE - Checks alignment of bore centerline and firing pin hole.#080-722-300AS .38 Barrel Alignment Gauge,

8K22A35 � � � � � � � � � � � � � � � � � � � � � � � � � � $ 24.99

◯24 #90 PIN VISE - Double-ended to fit pins up to .125".#345-090-000AS Pin Vise No. 90, 5D15H49 � � � � � � � � � � � �$ 15.49

◯25 CRANE STRETCHER - Cures excess cylinder movement.#080-640-000AS Crane Stretcher, 8K28C44 � � � � � � � � � � �$ 35.99

◯26 950-252 FEELER GAUGE - Checks barrel/cylinder gap.#606-950-252AS Inch Feeler Gauge, 8K27Q99 � � � � � � � � �$ 27.99

◯27 REVOLVER FITTERS BENCH BLOCK - Two holes, one slot provide solid surface for driving pins, polishing.#080-631-000AS Bench Block, 8K46K21 � � � � � � � � � � � � � �$ 55.99

ARMORER’S KIT BOX - With distinctive Armorer’s Kit label.#080-200-303AS Armorer’s Kit Box, 8K11E77 � � � � � � � � � �$ 15.99

① MEDIUM INDIA STONE - Removes burrs and roughness.#657-246-146AS MF-46 India Stone, 7E9M75 � � � � � � � � � �$ 10.99

② BROWNELLS YOKE/CRANE ALIGNMENT TOOLS - Shows any misalignment due to a bent yoke.#080-616-001AS #1 Yoke/Crane Tool, 8K27M28 � � � � � � $ 34.99#080-616-002AS #2 Yoke/Crane Tool, 8K42M98 � � � � � � 56.99

③ BROWNELLS YOKE/CRANE REAMER - Removes burrs and restore I.D. after swaging or “stretching”.#080-627-000AS Yoke/Crane Reamer, 8K28K27 � � � � � � $ 34.99

④ BROWNELLS NYLON WEDGE - Bends the yoke to restore proper alignment, adds “arch” to mainspring to lighten trigger.#080-722-100AS Nylon Wedge, 8K11N81 � � � � � � � � � � � � � $ 14.99

⑤ BARRETTE FILE - For smoothing, fitting.#191-350-370AS 4" Barrette #1 Cut, 6C20H62 � � � � � � � �$ 23.99

⑥ BROWNELLS CUP TIP PUNCHES - Fit round head S&W pins to prevent pin flattening. Six sizes included.#080-620-306AS Cup Tip Punch Set C, 8K76E05 � � � � � � $ 89.99

⑦ BROWNELLS BRASS DRIFT PUNCH#080-475-300AS Brass Drift Punch, 8K4B80 � � � � � � � � � � � � $ 7.99

⑧ BROWNELLS MAGNETIC PIN STARTERS - Hold the round head Smith pins securely for no-slip, no-scratch reassembly.#080-242-057AS Small Pin Starter, 3K10H80 � � � � � � � � � $ 16.84#080-242-070AS Medium Pin Starter, 8K8K66 � � � � � � � � 13.99

⑨ BROWNELLS S&W HAND PIN HOLDER#080-722-200AS S&W Hand Pin Holder, 8K8P00 � � � � � � � $ 9.99

⑩ BROWNELLS BABBITT BARS - Give cushioned “hammer” blow for loosening side plate, correcting alignment.#084-172-001AS Round Babbitt Bar, 4H17B00 � � � � � � � � $ 19.99#084-172-002AS Trapazoid Babbitt Bar, 8K21M60 � � � � 31.99

⑪ BROWNELLS .38 SERVICE RANGE ROD - Accurate check of each cylinder chamber’s alignment to axis of the bore.#080-617-038AS .38 Service Range Rod, 8K29G30 � � � � $ 39.99

⑫ BROWNELLS 82° COUNTERBORE - For deburring/ chamfer-ing of larger holes than the broaches can handle#080-722-820AS 82° Counterbore, 8K16C76 � � � � � � � � � $ 19.99

⑬ BALLPEEN HAMMER#956-000-002AS 4 oz. Ballpeen Hammer, 9D29Q98 � � $ 29.99

⑭ BROWNELLS EXTRACTOR SUPPORT - Takes load off extrac-tor, ejector star, and guide pin during ejector rod removal.#080-720-038AS .38/.357 Extractor Support Tool,

8K23M93 � � � � � � � � � � � � � � � � � � � � � � � � � � �$ 29.99

TOOLS FOR SMITH & WESSON REVOLVERS41 Tools - And More - Specifically For Servicing Smith & Wessons

135

1410

2425

#080-722-010AS Armorer’s Service Kit, All Tools Plus Box, 8K536J87 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �$ 580.99#080-722-002AS Armorer’s Kit Tools, only, 8K514Q78 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 569.99

TOOLS INCLUDED IN S&W TOOL KIT

Installs and removes front sights for Glock pistols. Large, hex-shaped grasping surface gives you a secure purchase and plenty of leverage. Also fits Walther P99, Smith & Wesson SW99, and other pistols with sights that use 3/16" hex head screws. abSPECS: Aluminum, anodized finish. Fits 3/16" hex head front sight screws for all Glock pistols.

HIVIZ

FRONT SIGHT TOOL for GLOCK®/ WALTHER P99/S&W SW99

Handy Pocket Tool For Removing/Installing/Tightening Up Sight

Screw

#638-000-188AS Glock Front Sight Tool, 8C11K11 � � � � � � $ 11.99

Slides into the dovetail and holds the striker plung-er spring and cap in place for hassle-free rear sight installation. Speeds the job

and lessens the risk of losing the spring or cap. Tough polymer tip resists wear, plus won’t mar the slide or sight finish. Contoured for easy, non-slip grasp between thumb and finger. abSPECS: Polymer, black. 2" (5.1cm) long. Fits rear sight dovetail on all Smith & Wesson M&P semi-autos.

TALON TACTICAL S&W M&P

REAR SIGHT TOOLRetains Striker Spring For

Easy Sight Installation

#100-005-388AS Rear Sight Tool, 5C3D12 � � � � � � � � � � � � � �$ 3.99

Set back new or existing bar-rels to tighten barrel/cylinder gap, without a lathe. abSPECS: Fixture includes steel fixture body, 27/8" (7.3cm) long. Adjustable carbide cutter, one .38/.357 bore pilot, adjustable pilot carrier, and Allen wrench. Master Kit includes all of the above and pilots for, .22RF, .32, .38/.357, .41, .44 and .45.

BARREL SET-BACK FIXTURERelieve Revolver Barrel

Shoulders Without A Lathe

#080-762-380AS Barrel Set-Back Fixture, 8K127A89 � � $ 154.99#080-762-000AS Barrel Set-Back Master Kit,

8K195E89 � � � � � � � � � � � � � � � � � � � � � � � � 257.99#080-762-001AS Replacement Cutter, 8K23F80 � � � � � 30.99

Takes the guesswork out of determining how wide to mill the dovetail cut. Lets you make fast, fin-ished cuts within .0005". Measures sights and dovetails. abSPECS: Aluminum base, matte black finish. Steel pins. Base 2" (5.8cm) x 2" (5.8cm) x 1.1" (2.8cm). Includes charts, instructions.

XS SIGHT SYSTEMS

DOVETAIL MEASURING TOOLDetermines Sight & Dovetail

Width

#006-101-000AS Dovetail Measuring Tool, 6K46E35 � � $ 54.00

Pocket tool helps you per-form most of the tasks required to maintain a Smith & Wesson K, L, or N frame revolver. Great for quick repairs and adjustments in the field or at the range. Includes screwdriver bits for the grip screws and strain screws, plus the screws for the side plate, yoke, cylinder thumb piece latch nut, and adjustable rear sight. Use it to remove/ install the rebound slide and rebound slide spring, as well as to tighten/loosen the extractor rod without damaging the knurling on the tip of the rod. Strong internal magnets retain the driver bits and help keep small steel parts from rolling away during field or bench disassembly. Driver bits are hol-low ground to ensure full-surface contact with the screw slots. abSPECS: 6061 T6 aluminum body, hardcoat anodized, matte black, with hardened steel 210-2 and 150-3 bits. 31/4" (8.2cm) long, 3/4" (1.9cm) wide, 1/2" (1.3cm) thick. 2 oz. (57g) wt. For Smith & Wesson K, L, and N frame revolvers.

S&W K/L/N FRAME SPD TOOLBasic Maintenance Tool Kit

That Fits In Your Pocket

#080-000-820AS S&W Revolver SPD Tool, 1B45H93 � � � $ 49.99

Prevents springing the frame by using fitted inserts that exactly match the con-tours of the revolver frame and distribute the turning forces evenly over it. abSPECS: Steel handle, aluminum head, Del-rin® insert. 151/4" (39cm) overall length. 3" (7.6cm) wide 41/2" (11.4cm) includes lock screw). 1" (2.5cm) thick. .755" (19.2mm) handle diameter. Weighs 13/4 lb. (794 g) w/o

insert. Inserts weigh 61/2 oz. (184.3g).

MGW, LTD.

CONTOUR FITTED REVOLVER FRAME WRENCH

Professional Tool Prevents Springing Frame

STK# WRENCH W/1 INSERT

STK# FRAME INSERT ONLY

MODEL

#584-200-002AS #584-100-002AS Colt Python & Officers’ Mod.t#584-200-003AS #584-100-003AS S&W “L”#584-200-004AS #584-100-004AS S&W “K”#584-200-005AS #584-100-005AS S&W “N”#584-200-006AS #584-100-006AS Ruger Blackhawk®/Colt SAA

— Advise # — Wrench w/1 Insert, 4H119E49 � � � � � � � � � $ 147.57— Advise # — Frame Insert Only, 4H30A99 � � � � � � � � � � 38.27

Visit brownells.com/dream

PAGE 486 Office/Tech: 641-623-5401SATISFACTION GUARANTEED

SINCE 1939

SPE

CIA

LTY

N T

Our Revolver Ac-tion Wrench com-pletely surrounds

and supports the frame with special no-mar aluminum heads to prevent twisting and gouging. Heads fit existing Brownells Action Wrench System handle or start with the complete unit shown here and then add other handgun and rifle heads as needed. abSPECS: Base/Handle Unit - Steel, blued. 123/4" (31cm) long, 1" (2.5cm) diameter handle. Interchangeable Heads - Aluminum 3/4" (19mm) square, 51/5" (14cm) long. Complete Wrench - Includes Base/Handle and heads for one gun model, bolts and instructions. Complete Wrench or Heads Only to fit double action revolvers.

SINGLE ACTION, ACTION WRENCHES - Aluminum heads com-pletely enclose those fragile frames to help eliminate damage.SPECS: Base/Handle Unit - Steel, blue. 123/4" (31cm) long, 1" (2.5cm) di-ameter handle. Interchangeable Heads - Aluminum, 3/4" (19mm) square, 51/8" (14cm) long. Complete Wrench - Includes Base/Handle and heads for one gun model, bolts and instructions. Ruger fits Blackhawk®, Super Blackhawk® and Vaquero® size frames.

STK# COMPLETE WRENCH STK# HEADS ONLY FITS#080-800-173AS #080-801-073AS Colt SAA#080-800-174AS #080-801-074AS Ruger

— Advise # — Complete Wrench, 8K110A65� � � � � � � � � $ 139.99— Advise # — Heads, only, 8K80N10 � � � � � � � � � � � � � � � 114.99

REVOLVER ACTION WRENCHCompletely

Surrounds Revolver Frames To Prevent Expensive Torque

Damage

STK# COMPLETE WRENCH STK# HEADS ONLY FITS#080-850-002AS #080-851-002AS S&W K Frame#080-850-003AS #080-851-003AS S&W L Frame#080-850-004AS #080-851-004AS S&W N Frame

— Advise # — D/A Revolver Wrench, 8K110P92 � � � � � � $ 139.99— Advise # — D/A Revolver Wrench Heads, only,

8K75Q47 � � � � � � � � � � � � � � � � � � � � � � � � � � � 106.99

Robust tool gives you enough length and leverage to remove even the most stubborn pins without marring the frame.

Double-ended tool precisely fits Ruger revolvers on one end and Colts on the other, so base pins on the most popular cowboy guns can be pulled with one convenient tool. abSPECS: Steel, black. 5" (12.5cm) long. Fits Ruger and Colt revolver base pins.

SA REVOLVER

DOUBLE-END BASE PIN PULLERPops Loose Stuck Base Pins On Ruger® & Colt Revolvers

#080-000-367AS Double End Base Pin Puller, 8K23K99 � � � � � � � � � � � � � � � � � � � � � � � � � � $ 39.99

Hardened steel bar hooks into the groove in the head of the base pin to gently pull pins out of the frame without marking pin or frame. Fits Colt, and some clone, factory pins. abSPECS: Steel, blue finish. 31/2" (8.9cm) long.

RIMFIRE GUN WORKS SA REVOLVER

BASE PIN PULLERGently Pop Base Pins Loose

#777-000-001AS Colt Base Pin Puller, 7G20N90 � � � � � � �$ 22.99#777-000-002AS Base Pin Puller for Ruger SA,

7G20B90 � � � � � � � � � � � � � � � � � � � � � � � � � � � 22.99

Because both Ruger and S&W’s lock at the front and rear of the extractor rod, even a slightly bent one can cause difficulty in lockup and will impair smooth operation, especially for doubleac-tion shooting. These tools help precisely align the crane in just min-utes, without “guesswork”. Precision ground and hardened to within .0005" on all critical dimensions to assure the ultimate in accuracy. Instructions included. Hardened to Rc 52-54. abSPECS: J - 2.6" (6.6cm) long; K - 3.17" (8cm) long; Ruger® - 3.025" (7.6cm) long. #1 for S&W “J” Frame (centerfire only); #2 for S&W “K”, “L” or “N” Frame; #3 for Ruger Speed-Six® and Security-Six®. Shorten knurled end to fit 2-2-1/2" barrel revolvers.

YOKE/CRANE ALIGNMENT TOOL

.0005" Tolerances For Ultimate Accuracy

#080-616-001AS #1 Yoke/Crane Tool, 8K28Q66 � � � � � � �$ 34.99#080-616-002AS #2 Yoke/Crane Tool, 8K46L06 � � � � � � � 56.99#080-616-003AS #3 Yoke/Crane Tool, 2C25H03 � � � � � � � 30.95

Removes all burrs and roughness from inside the Ruger “Six” Series D.A. and S&W K/L/N crane. Also restores crane to proper di-mensions after “stretching” to eliminate endshake. abSPECS: 71/2" (19.0cm) overall. Precision-ground, hardened tool steel reamer with six straight cutting blades. Tenite handle.

YOKE/CRANE REAMERFrees-Up Ejector Springs; Restores I.D. Dimension

#080-627-000AS Yoke/Crane Reamer, 8K30A29 � � � � � � $ 34.99

Heavy-duty, high-leverage, wrench and Del-rin® blocks give form-fitted support of the frame for barrel removal and other customizing jobs. Frame Blocks fit around the entire frame to provide maximum support for changing the barrel or custom machining operations like opening up the rear sight notch, making dovetails, or disassembling internal parts. Insert Blocks fit on the front of the frame and are used only for barrel removal/installation and tightening or loosening the barrel to regulate sights. Non-marring, aluminum Barrel Blocks convert the wrench handle into a barrel wrench. Use two handles, one with frame blocks, one with barrel blocks to remove barrel from frame without a vise. Blocks alone work great as vise jaws. abSPECS: Handle - Steel. 14"(35.6cm) long, 1" (2.5cm) wide, 1" high. Includes Allen wrenches. Frame Blocks - Delrin, black. 31/8"(7.9cm) long, 3/4" (1.9cm) wide, 27/16" (6.2cm) high. Ruger SA fits all Ruger single action frames. Colt SAA fits Colt Single Action Army and clones. Insert Blocks – Delrin, black. S&W K/L fits Smith & Wesson K and L frames. S&W N fits N frame. CSA/RSA fits all Colt SAA and clones, plus Ruger® Old/New Vaquero®, Blackhawk®,

POWER CUSTOM

REVOLVER FRAME/BARREL WRENCHSeparate Barrels &

Frames; A Third Hand For Most Disassembly Jobs

#713-000-024AS Frame/Bbl Wrnch Hndl, 3A85B91 � � � � $ 89.99#713-000-025AS Ruger SA Frame Blocks, 3A96E23 � � � � 99.99#713-000-026AS Colt SAA Frame Blocks, 3A96E23 � � � � 99.99#713-000-086AS S&W K/L Insert Blocks, 3A44A66 � � � � 49.99#713-000-087AS S&W N Insert Blocks, 3A44B66 � � � � � � 49.99#713-000-088AS CSA/RSA Insert Blocks, 3A44K66 � � � � 49.99#713-000-027AS Uni. SA Barrel Blocks, 3A34D66 � � � � � 36.99

and large-frame old-model three-screw single action revolvers. Barrel Blocks - 6061 T6 aluminum. 45/8" (11.7cm) long, 1" wide, 1" high.

Don’t let a stuck bullet from a “squib” or weak load cut short a shooting session. Far superior to other rods or makeshift punches, this non-marring brass rod fits the bore closely, can’t wedge between bullet nose and rifling. Each rod is drilled and tapped to thread onto, or adapt to, a Dewey or other cleaning rod; very handy for knocking stuck bullets out of rifle barrels. abSPECS: Kit contains one of each size rod and (2) 8-32 to 12-28 adapters. 8" (20.3cm) long. Brass. Pak has 2 rods of size listed and 2 Dewey rod adapters.

SQUIB ROD

No-Mar Brass Rod Knocks Stuck Bullets Out Of Bores

STOCK # FITS PRICE#084-175-032AS .32 Cal. 4H25L34 $ 29.99#084-175-357AS 9mm/.38/.357Cal. 4H25A34 $ 29.99#084-175-040AS 10mm/.40/.41 Cal. 4H25I83 $ 29.99#084-175-044AS .44 Cal. 4H25K34 $ 29.99#084-175-045AS .45 Cal. 4H25P34 $ 29.99

#084-175-000AS Squib Rod Kit, 4H69I87 � � � � � � � � � � � � � �$ 85.99— Advise # — Squib Rod Pak, 4H25L34 � � � � � � � � � � � � $ 29.99

Check the yoke/crane assembly and ejector rod for bends; straightening handles fix the problem for S&W K/L/N Frame. abSPECS: Base, steel. 10" (25.4cm) long, 2" (5cm) wide, 5" (12.7cm) high. Alignment

Rod, 10" (25.4cm) long, 9/16" (14.3mm) dia., heat-treated, blued, steel. With instructions - Dial Indicator NOT included.

POWER CUSTOM S&W EXTRACTOR ROD & YOKE ALIGNMENT TOOL

Test & Straighten, Fast!

#713-025-000AS Extractor Rod/Yoke Alignment Tool, 3A124Q59 � � � � � � � � � � � � � � � � � � � � � � � � $ 129.99

#606-141-000AS 1410 Dial Indicator, 6K96P99 � � � � � � 96.99

Easy to use tool enables fast removal and reinstallation of screw-in extractor rods from double action revolvers without damage to rod or cylinder yoke.

Specifically designed for Smith & Wesson J/K/L/N frame models and Ruger® Security-Six® and Speed-Six®, but will work on almost any similar screw-in rod. Just slide the extractor rod into the correct-size grooves on the tool, close the tool halves around the rod by tightening the two hex head bolts on either side of the rod using the included Allen wrench, and simply unscrew the rod with the tool while holding the cylinder. Grooves are precision machined to provide complete, 100% contact with the rod. Tool body of 6061 T6 aluminum is strong enough to provide years of service, yet soft enough to aid in securely gripping polished steel extractor rod with-out slippage or marring of rod surface. abSPECS: Aluminum, anodized, natural silver finish. Steel bolts, black oxide finish. Fits Smith & Wesson J, K, L and N frame revolvers and clones, Ru-ger Security-Six/Speed-Six, and older revolvers with button heads on the extractor rod front. Includes hex wrench and instructions.

POWER CUSTOM

UNIVERSAL EXTRACTOR ROD WRENCH

Easily Removes Screw-In Extractor Rods Without

Damage To Rod Or Cylinder Yoke

#713-000-083AS Universal Extractor Rod Wrench, 3A26K53 � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 27.99

Swages a small groove in the rear of the crane/ yoke tube, lengthening it to remove excess cylinder play. Also swages the re-taining groove in .22 magazine tubes. abSPECS: 31/2" (9cm) long. Capacity; 1/8" (3.2mm) - 5/8" (15.9mm).

CRANE STRETCHERQuickly Swages Crane To

Remove Cylinder Play; Cures Excess Headspace

#080-640-000AS Crane Stretcher, 8K28C44 � � � � � � � � � � $ 35.99

Swages and lengthens the gas ring to tighten frame-to-cylinder fit on single action revolvers. Fits Ruger single ac-tions with 1/4" diameter base pin.

Adapts for Colt 3rd Gen. and others with integral gas ring. abSPECS: Steel, hardened contact points. 2" (5cm) long. Kit includes stretch-er jaws, support pin, handle and lapping sleeve.

SINGLE ACTION

GAS RING STRETCHERTightens

Cylinder-To-Frame Fit

#080-952-000AS Gas Ring Stretcher, 8K74E74 � � � � � � � � $ 86.34#080-000-065AS Replacement Jaws, 8K24F90 � � � � � � � 28.99

Specially bent and slotted tool is really about the only way to get past the frame pin to grab and compress the rebound slide spring (without a lot of $%*!#*) while removing or installing the rebound slide. Fits all J, K, L and N frames. Will not scratch that valuable frame, pinch or bind. abSPECS: 6" (15.2cm) long, 1.015" (25.8cm) diameter.

S&W REBOUND SLIDE SPRING TOOLCorrectly and Easily Compresses Spring

#080-666-000AS Rebound Slide Tool, 3K15H88 � � � � � � � �$ 19.99

PAGE 487Orders/Tech: 800-741-0015order on the web

brownells.com

SPE

CIA

LTY

N T

Need a Replacement Part?

Shop the Factory Parts section in this catalog

Schematics also available online

Lets you know instantly if a revolver barrel and cylinder are in perfect alignment and if cylinder crane or yoke has been sprung, thus throwing axis of each out of line with axis of barrel bore . . . for timing - “accuracy jobs” . . . locating cause of lead splatter . . . professional service inspections. An excellent tool to use when demonstrating to a customer “why”! The handle with knurled grip end is threaded to take any of the interchangeable heads, with sizes carefully selected to indicate very small misalignments. The .38 cali-ber heads are available in two diameters, one for Match guns that must be dead on for best performance and one for Service guns which aren’t always thoroughly clean and don’t have to meet quite as fine an accuracy standard. And, there’s a special head for the S&W K-22 which has a slightly undersized bore. abSPECS: 101/2" (26.7cm) long handle. 21/2" (6.3cm) long heads made of steel hardened to Rc 52-54. Includes instructions. Heads interchange on handle except .17 Cal. Range Rod Handle fits only the .17 Cal. Range Rod Head. Combo includes Handle, one (1) Head and Instructions. Master Kit contains one (1) .22 to .45 Cal. Range Rod Handle and one (1) .17 Cal. Range Rod Handle, plus one (1) each of following heads: .17 Cal., .22LR, K-22, .22 Magnum, .32-20, .32 S&W/H&R Magnum, .38/.357 Match, .38/.357 Service, .41 Magnum, .44/40, .44/.44 Magnum, .45 ACP/.45 Colt in a fitted Storage Box. Match Kit has one (1) Handle, six Heads (all except the .38/.357 Service and K-22 Heads) in a fitted Storage Box. Add-On Pack includes one (1) .17 Cal. Range Rod Handle, plus one each of following heads: .17 Cal., K-22, .22 Magnum, .32-20, .38/.357 Service, .44/40, plus pre-cut foam to accommodate all items in existing Range Rod Match Kit box. See chart for Head only and Combo Stock #’s.

REVOLVER RANGE RODS

Tells Instantly If Barrel & Cylinder Are In Perfect Alignment - Match &

Service Grade Available

#080-617-038AS .38 Service Range Rod, 8K31Q40 � � � � $ 39.99#080-619-000AS .22-45 Range Rod Handle, 8K22E11 � � 29.99#080-619-001AS .17 Cal. Range Rod Handle, 8K10D15 � � 12.99#080-616-000AS Range Rod Match Kit, 8K112N88 � � � � 129.99#080-616-005AS Range Rod Master Kit, 8K171G45 � � � � 189.99#080-616-004AS Range Rod Add-On Pack, 8K67J28 � � 69.99

STK# HEAD STK# COMBO CALIBER#080-618-017AS #080-617-017AS .17 Cal.#080-618-022AS #080-617-022AS .22LR#080-618-001AS #080-617-001AS .22 Mag#080-618-032AS #080-617-032AS .32 S&W & H&R Mag#080-618-002AS #080-617-002AS .32-20#080-618-213AS #080-617-213AS S&W K-22#080-618-038AS #080-617-038AS .38/357 Service#080-618-138AS #080-617-138AS .38/357 Match#080-618-041AS #080-617-041AS .41 Mag.#080-618-044AS #080-617-044AS .44/44 Mag.#080-618-003AS #080-617-003AS .44/40#080-618-045AS #080-617-045AS .45 ACP/45 Colt

— Advise # — Range Rod Head, 8K26M05 � � � � � � � � � � � �$ 29.99— Advise # — Range Rod Combo, 8K32F77 � � � � � � � � � � � 39.99

Adding a spring-loaded, locking ball in the cylinder crane is standard practice on Smith & Wesson K, L and N Frame revolvers, especially when installing a bull barrel. Steel fixture holds the crane secure and in proper align-ment for drilling; makes it vir-tually impossible to mislocate the hole or drill at the wrong angle. Comes complete with No. 30 drill bit, .125" diameter locking balls, springs, and staking punch. abSPECS: Drilling Fixture - Steel, blued finish. 11/2" (3.8cm) long, 1" (2.5cm) wide, 2" (5.1cm) high. Includes No. 30 cobalt drill bit, (20) 302 SS locking balls, 20 springs, and staking punch. Crane Ball & Spring Kit - Contains 20 locking balls, 20 springs, and staking punch. Crane Ball & Spring Re-fill - Contains 10 balls and 10 springs. Designed for K, L and N Frame yokes only.

POWER CUSTOM SMITH & WESSON

CRANE BALL DRILLING FIXTURE

#713-000-052AS Crane Ball Drilling Fixture, 3A66F33 � � $ 69.99#713-035-000AS Crane Ball & Spring Kit, 3A18N05 � � � � 18.99#713-035-001AS Crane Ball & Spring Refill, 3A6N08 � � 6.99

Add Cylinder Lockup Strength The Foolproof Way

Holds the gate detent spring to re-lease its pressure from the hammer and trigger pivot pins, plus the hammer and trigger/transfer bar groups. abSPECS: Aluminum.

RUGER® SA

GATE DETENT SPRING CLAMPA Third Hand For Disassembly/

Reassembly

#080-906-000AS Gate Detent Sprg Clmp, 8K21I78 � � � � $ 25.99

Heat-treated, steel bit fits in our Magna-Tip handle and helps you remove the ejector retainer screw; a “must do” step for com-plete disassembly of Ruger D/A cylinders. Self-aligns perfectly over the center pin rod during removal. abSPECS: Steel. 1.95" (5cm) long. Works with Ruger double-action revolv-ers only.

RUGER®

EJECTOR RETAINER BIT

Helps You Easily Disassemble Redhawk®, Super Redhawk® GP-100®, & SP101® Cylinders

#080-432-001AS Ruger D/A Ejector Bit, only, 8K7G59 � � �$ 8.99

On the bench or in the field, you'll have the

right screwdrivers for your gun in one compact, go-anywhere package. We precisely matched each gun’s screws to the correct Magna-Tip ® bits to give you the best possible, blade-to-slot fit. Ex-cept where indicated otherwise, each set comes with a magnetic socket, Hollow Handle for easy, on-board storage of the bits. ab

COLT SINGLE ACTION - Five bits to fit all the screws on Colt Single Actions and popular clones.SPECS: 8" (20.3cm) long overall. 11/4" (3.2cm) diameter grip.#080-000-021AS Colt SAA Set, 8K19H55 � � � � � � � � � � � � � �$ 21.99#080-000-086AS Colt SAA Bits, only, 8K8N54 � � � � � � � � � � 9.99

RUGER® SINGLE ACTION - Four flat blade bits to fit Ruger Single Action screws for base pin latch, grip frame, and ejector housing, plus an extra-long hex bit for Bisley backstrap screws.SPECS: 8" (20.3cm) long overall. 11/4" (3.2cm) diameter grip. Bits fit Ruger Blackhawk®, Vaquero®, Bisley, and 2005 and later New Vaquero®.

#080-000-020AS Ruger S/A Screwdriver Set, 8K20L85 � �$ 29.99#080-000-087AS Ruger S/A Bits, only, 8K10D79 � � � � � � � � 14.99

S&W REVOLVER COMBO - Four bits to fit side plate, grip, thumb latch, and rear sight elevation and tang screws.SPECS: 8" (20.3cm) long overall. 11/4" (3.2cm) diameter grip.#080-087-004AS 4-in-1 S&W Combo, 8K15G85 � � � � � � � � $ 17.95#080-087-002AS S&W Combo Bits, only, 8K7M13 � � � � � � 7.99

S&W SCREWDRIVER - Three custom bits for S&W Strain, Windage, Side Plate and Sight attaching screws. Comes with Clip-Tip Law Enforcement Handle for excellent control. No stor-age compartment in grip.SPECS: 51/2" (14cm) long overall. 1" (2.5cm) diameter grip.#080-088-003AS S&W Screwdriver Set, 8K15J35 � � � � � � �$ 16.99#080-088-005AS S&W Bits, only, 8K5B12 � � � � � � � � � � � � � � 5.99

GUN SPECIFIC SCREWDRIVER SETSSelf-Storing, Carry Along For ’Smiths &

Shooters

You can’t get a great action job without clean-ing up every bit of roughness inside the Single Action Army’s frame. You’ll be amazed at how much you can reduce the single action’s co*cking effort and lighten perceived trigger pull without ever touch-ing the critical trigger/hammer notches. Well worth the effort on first and second generation Colts, especially important on 3rd genera-tion and clones with cast or roughly forged frames. The MF-414 stone fits nicely in the hand slot and cuts quickly to get rid of cast-ing roughness. Follow with the HF-823 to make a slick, polished path for the hand. Use the MF-14 to round the nose of the hammer notch. Thanks to Eddie Janis of Peacemaker Specialists for his help with this kit. abSPECS: Kit contains three stones in padded plastic box: MF-414, MF-14 and HF-823. Dimensions are approximate and may vary. MF-414 - me-dium India, 5/16" (7.9mm) wide x 3/16" (4.8mm) thick, tapers to 1/16" (1.6mm) thick x 4" (10cm) long; MF-14 - medium India 1/4" (6.3mm) square x 4" long. HF-823 - hard Arkansas 3/8" (9.5mm) wide x 1/8" (3.2mm) thick x 31/8" (7.9cm) long.

COLT SINGLE ACTION HAND SLOT STONING KIT

Smooth Those Hard-To-Reach Spots

For Lightest Pull

#657-414-002AS MF-414 Stone, 8K14L99 � � � � � � � � � � � � $ 14.99#657-214-141AS MF-14 Stone, 8K9I99 � � � � � � � � � � � � � � � 9.99#657-300-823AS HF-823 Stone, 8K31D52 � � � � � � � � � � � � 32.99#080-904-000AS Single Action Stoning Kit, 8K52I99 � � 52.99

Polish rough or scored revolver chambers smooth and friction-free in only minutes to cure many extraction problems. Machine marks on semi-auto pistol spring “ways” disappear for smoother, faster hammer fall and improved cycling. Use Flex-Hone Oil Only. abSPECS: Medium and Fine grit silicon carbide abrasive, twisted steel shafts. Must be used with Flex-Hone oil. Cylinder, M/S Housing Hones: 3" (7.6cm) long; 1911 Slide Lug Area Hone: 8" (20.3cm) long.

STK# MED. STK# FINE FITS#080-608-132AS #080-608-232AS .32 Cylinder#080-608-138AS #080-608-238AS .357/.38 Cylinder

NA #080-608-241AS .41 Cylinder#080-608-144AS #080-608-244AS .44 Cylinder#080-608-145AS #080-608-245AS .45 ACP Cylinder#080-608-146AS #080-608-246AS .45 Colt Cylinder

— Advise # — Cylinder Polishing Hone, each, 8K26I28 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 31.95

1/2 PINT FLEX-HONE OIL - Specially formulated for use with Flex-Hone brushes. Use of other oils destroys abrasive balls and voids warranty. ab#080-609-008AS 1/2 Pint Flex Hone Oil, 1B10F92 � � � � � � $ 13.49

FLEX-HONE

HANDGUN POLISHING SYSTEMSilicon Carbide Abrasive Balls For Flawless “Inside” Polishing

On Revolvers & Semi-Auto Pistols

#080-608-212AS 1911 Auto Slide Lug Area Hone, Fine, 1B28N98 � � � � � � � � � � � � � � � � � � � � � � � � � � �$ 34.95

#080-608-001AS 1911 Auto Slide Lug Area Hone, Med., 8K29B30 � � � � � � � � � � � � � � � � � � � � � � � � � � � 34.99

STK# MED. STK# FINE FITS#080-608-111AS #080-608-211AS 1911 M/Spring Housing

— Advise # — Mainspring Housing Hone, 1B27Q35 � � � �$ 31.99

Custom made to fit the oddball threads on S&W K, L and N, and Ruger® GP100® barrels/frames. Absolutely essential when rebarrel-ing. Perfect for cleaning up damaged threads. abSPECS: High speed steel. Colt Single Action, .695" - 20 thread, 11/2" dia. die. J Frame, .500"-36 threads. 1" dia. die. K Frame, .540"- 36 threads. 1" dia. die. L Frame, .562"-36 thread, 11/2" dia. die. N Frame, .670"-36 thread, 11/2" dia. die. Ruger Single Action (centerfire), .680" - 24 thread, 11/2" dia. die. GP100, .625"-24 thread, 11/2" dia. die. Redhawk® (all models): .750"-20, 11/2" dia. die.

REVOLVER TAPS & DIES

#080-598-695AS Colt SA Tap, 5B37M33 � � � � � � � � � � � � � � $ 49.99#080-598-696AS Colt SA Die, 5B62J61 � � � � � � � � � � � � � � � 69.99#080-598-536AS J Frame Tap, 5B20J72 � � � � � � � � � � � � � � 24.97#080-598-537AS J Frame Die, 7C19L56 � � � � � � � � � � � � � � 20.99#080-598-540AS K Frame Tap, 2K38G24 � � � � � � � � � � � � � 44.99#080-598-541AS K Frame Die, 2K60B10 � � � � � � � � � � � � � � 69.99#080-598-562AS L Frame Tap, 2K51J44 � � � � � � � � � � � � � � 55.99#080-598-563AS L Frame Die, 2K77E15 � � � � � � � � � � � � � � � 84.99#080-598-670AS N Frame Tap, 2K53E57 � � � � � � � � � � � � � � 59.99#080-598-671AS N Frame Die, 2K87L87 � � � � � � � � � � � � � � 94.99#080-598-680AS Ruger SA Tap, 5B43G40 � � � � � � � � � � � � 47.99#080-598-681AS Ruger SA Die, 5B57A71 � � � � � � � � � � � � � 78.13#080-598-625AS GP100 Tap, 2K51C68 � � � � � � � � � � � � � � � 67.99#080-598-626AS GP100 Die, 2K77M98 � � � � � � � � � � � � � � � 95.99#080-598-750AS Redhawk Tap, 7C21C63 � � � � � � � � � � � � 24.99#080-598-751AS Redhawk Die, 7C30B25 � � � � � � � � � � � � 31.99

Clean Up Threads On Popular Revolvers During Rebarreling & After Lathe Threading

PAGE 488 Office/Tech: 641-623-5401SATISFACTION GUARANTEED

SINCE 1939

SPE

CIA

LTY

N T

Steel cutting tool removes burrs from the outer edge of the forcing cone to improve accuracy. Use on the chamber throat to help rounds drop in easily. Eliminates lead shaving or “spitting” in one or two passes. Unique design works without disassembling the gun. 3/8" tool is ideal for .17 and .22 revolvers. 1/2" tool works on revolvers from .32 through .45. Revolver Deburring Tool includes cutter and handle. Cutters also sold separately and can be interchanged in the handle. abSPECS: Cutter - High speed steel, hardened. 3/8" (9.5mm) O.D. Handle - Aluminum, 3" (7.6cm) long.

REVOLVER DEBURRING TOOL & CUTTERS

#080-623-000AS 1/2" Revolver Debur. Tool, 8K39M45 � � $ 44.99#080-623-001AS 3/8" Revolver Debur. Tool, 8K41F86 � � � 44.99#080-623-002AS 1/2" Revolver Deburring Cutter, only,

8K30D37 � � � � � � � � � � � � � � � � � � � � � � � � � � 32.99#080-623-003AS 3/8" Revolver Deburring Cutter, only,

8K27C97 � � � � � � � � � � � � � � � � � � � � � � � � � � 29.99

1/2" cutter

3/8" cutter

Cuts Quick, Duty Gun Chamfer In Small Cylinders

#080-654-000AS Crane Bushing Tool, 8K21M78 � � � � � � $ 25.99

REVOLVER CYLINDER GAUGES - Quickly, accurately checks headspace on any .38/.357 revolver whose cylinder chambers are NOT recessed for the case rim. For Ruger S.A/D.A. and S&W’s.SPECS: 3" (7.6cm) x 7/16" (11.1mm). Hardened, ground tool steel.#080-633-666AS 60/66 Cylinder Gauge, 8K29H92 � � � � $ 34.97#080-633-668AS 60/68 Cylinder Gauge, 8K30K06 � � � � 35.99

RUGER S/A CENTER PIN LATCH TOOL - Use to hold the base pin nut on Ruger single ac-tions so you can take the latch apart.abSPECS: 4" (10cm) long overall. Hardened steel bit. 13/16" (20.6mm) diam-eter, plastic handle. Sorry, no breakage guarantee.#080-642-000AS Center Pin Latch Tool, 8K17B95 � � � � � $ 22.95

MAINSPRING COMPRESSOR - A “third hand” for revolver work. Con-trols mainspring and strut so you can remove or install retaining pin. Fits coil mainspring Ruger, Colt, S & W, Taurus and H & R revolvers, plus Ruger No. 1/3 rifles.SPECS: Steel, blued finish. 1" (2.5cm) wide, 61/4" (16cm) long.ab#080-927-000AS Mainspring Compressor, 8K43L33 � � � $ 55.99

NYLON WEDGE - Gently bends yoke to re-store proper alignment. Also “archs” main-spring to lighten trigger pull.SPECS: 5" (12.7cm) long overall. 1" (2.5cm) wide. Tapers from 1" (2.5cm) to 1/8" (3.2mm) thick.ab#080-722-100AS Nylon Wedge, 8K12B65 � � � � � � � � � � � � $ 14.99

ARMORER’S BRUSH - Gently removes metal filings, dirt, dust, bits of abrasive stone, etc., out of actions and recesses.abSPECS: Varnished wood handle. Natural bristles. 51/8" (13cm) long.#821-135-210AS Armorer’s Brush, 8K7N65 � � � � � � � � � � � � $ 8.99

S&W CYLINDER STOP & HAND WINDOW FILES - Double-ended, offset files open up the “window” in an S&W frame to accept a new cylin-der stop or hand.SPECS: Both are #2 cut and fit all S&W frames. Cylinder Stop File, 6" (15.2cm) long, Hand Window File, 6" (15.2cm) long.#360-318-731AS Cylinder Stop Window File,

6C30F99 � � � � � � � � � � � � � � � � � � � � � � � � � � $ 30.99#080-754-000AS Hand Window File, 6C31N78 � � � � � � � � 36.99

EXTRACTOR ROD TOOL - Machined aluminum clamp maintains a secure hold of the extractor rod for fast, easy removal without scratching or gouging the metal surface. Steel, Allen head screw tightens to pull the clamping halves to-gether for a non-slip hold. Grasp the tool and un-screw the extractor. Ensures professional- look-ing results everytime. Available for Smith & Wesson revolvers and the Ruger® Security-Six®. Recommended for use with Brownells adjustable extractor support tools.abSPECS: Aluminum, black. 11/2" (3.8cm) diameter x 1/2" (1.3cm) thick. S&W Small - .228" (5.8mm) I.D. Fits S&W J frame. S&W Large - .246" (6.3mm) I.D. Fits S&W K, L, and N frame. Security-Six - .266" (6.8mm) I.D. Fits Ruger Security-Six only.#080-000-536AS S&W Small Extractor Tool, 8K19Q24 � �$ 21.99#080-000-537AS S&W Large Extractor Tool, 8K19A48 � � 22.99#080-000-538AS Security-Six Extractor Tool, 8K19J27 � � 21.99

ADJUSTABLE EXTRACTOR SUPPORT - Brass rods support extractor guide pin and star when ejector rod is unscrewed.abSPECS: Body - Carbon steel. 27/8" (7.3cm) long, .500" (12.7mm) wide. Rods - brass. 13/16" (3cm) long, Rods Only, two supplied. Complete Set contains one Body and four Rods. .45 ACP and .45 Auto Rim use .44 Rods. Set of two.#080-720-038AS .38/.357 Extractor Support Tool,

8K23M93 � � � � � � � � � � � � � � � � � � � � � � � � � � $ 29.99#080-720-138AS .38/.357 Support Rods, only,

8K11M21� � � � � � � � � � � � � � � � � � � � � � � � � � � 14.97#080-720-044AS .44/.45 Extractor Support Tool,

8K23B46 � � � � � � � � � � � � � � � � � � � � � � � � � � 29.99#080-720-144AS .44/.45 Support Rods, only, 8K9J33 � � 12.99#080-720-000AS Extractor Support Set, 8K59P63 � � � � � 74.97

COLT CRANE BUSHING TOOL - Fits over ejector rod and down into the cylinder to reach and remove the Crane Bushing from Colt Python, Trooper, Detective Special, Pocket Positive and many others.abSPECS: Steel, hardened and drawn. Body; 13/8" (3.5cm) long, .316 in (8.03mm) dia. Handle is 2" (5.1cm) long.

REVOLVER TOOLS & ACCESSORIESSpecialized & General Tools For Wheel Guns

High-speed steel chamfer cutter makes perfect 45° angle cuts for easier cylinder filling with speed loaders. TiN coating on the cutting surface allows for smooth, chatter-free cuts on tough metals such as scandium. Also great for chamfering the muzzle on chrome-lined barrels. abSPECS: High-speed steel, TiN coating on cutting surface. Overall length: 2.4" (61mm). 5/8" diameter. Fits Brownells Muzzle and Cylinder Chamfer-ing Handle.

45° TiN COATED CYLINDER CHAMFERING CUTTER

Durable TiN Coating Cuts Chamfers In Toughest Metal

#080-588-626AS 5/8" TiN Chamfer Cutter, 8K56C04 � � � �$ 64.75

Everything you need to cut a perfectly centered, chatter-free, 5° chamfer. Kit includes cutters, plug gauges, pilots and handle; Very gentle angle provides the bullet with a smooth transition into the rifling, improves accuracy, reduces lead spitting and shaving. No lathe needed nor is it necessary to remove barrel. abSPECS: Packed in a fitted bench box. Fits all .357, .44 and .45 caliber revolvers. Includes instructions.

5° PLUG GAUGE & CHAMFER KIT

Gentle Angle Reduces Bullet Deformation For .357, .44 & .45 Calibers.

#080-000-022AS 5° Plug Gauge & Chamfer Kit, 8K220C57 � � � � � � � � � � � � � � � � � � � � � � � � �$ 277.99

In the past, there was only one acceptable way to install a front sight in a ramp - pound it in with a hammer from the side. This method frequently marred a beautiful finish and loosened or damaged the ramp. The Williams Front Sight Pusher is the easiest and best way to install a front sight in a ramp. Equal-izing the pressure on ramp and sight, it permits installation without marring or damaging. Eliminates excessive pressure on the ramp. Smoothly, accurately moves sight into exact position. abSPECS: Aluminum body is 43/8" (11.1cm) long x 1" (2.5cm) wide x 13/8" (3.5cm) high. Screw is steel.

WILLIAMS

FRONT SIGHT PUSHEREasiest Way To Install A Front Sight In A Ramp

#962-050-000AS Front Sight Pusher, 2F56N78 � � � � � � � � $ 60.99#962-050-001AS Front Sight Pusher Replacement

Jaws, 2F9G88 � � � � � � � � � � � � � � � � � � � � � 13.99

Cures the “ramp slips just as the solder melts” problem with a pointed, spring-loaded plunger that keeps constant pressure on the ramp or a .45 sight. Adjusts for height, angle and amount of spring pressure. Non-marring, “V” block base centers barrel under the plunger. Great torch clear-ance. abSPECS: 2" (5.1cm) long. aluminum Base. 4" (10.2cm) high overall.

RAMP SOLDERING JIGSpring Pressure Keeps Ramps/

Bases/.45 Sights In Place

#080-739-000AS Ramp Soldering Jig, 8K73E93 � � � � � � � $ 89.99

Easy to use, hand turned reamer opens the cylinder throat to a uniform diameter for best accuracy with lead and jacketed bullets. Corrects out of spec, smaller-than-bore-diameter cylinder throats. Removable pilots let you select the correct pilot for the closest pos-sible fit to individual chambers. .357 Cal. fits .357 Magnum and .38 Special. Opens throat to .358". Provided with .354" diameter pilot. .44 Cal. fits .44 Magnum, .44 Special and .44-40 revolvers. Opens throat to .431". Furnished with .4270" pilot. .45 Cal. fits on .45 Colt and other .45 caliber revolvers. Opens throat to .4525". Provided with .4480" diameter pilot. Pilot Packs contain six additional pilots in .0005" increments. .357 Cal. from .3545" to .3570". .44 Cal. from .4275" to .4300". .45 Cal. from .4485" to .4510". abSPECS: High-speed steel. 4" (10cm) long, 1/4" shank, 6 flute, helical ground.

MANSON PRECISION REVOLVER

CYLINDER THROATING REAMER

Improves Accuracy, Helps Eliminate Fliers

#513-000-078AS .357 Cal. Throat Reamer w/.354" Pilot, 3A80J00 � � � � � � � � � � � � � � � � � � � � � � � � � � $ 80.00

#513-000-079AS .357 Cal. Pilot Pack, 3A60M00 � � � � � � 60.00#513-000-030AS .44 Cal Throat Reamer, 3A80H00� � � � 80.00#513-000-031AS .44 Cal. Throater Pilot Pack,

3A60F00 � � � � � � � � � � � � � � � � � � � � � � � � � � 60.00#513-000-001AS .45 Cal. Throat Reamer, 3A80N00 � � � 80.00#513-000-002AS .45 Cal. Throat Pilot Pack, 3A60I00 � � 60.00

There is a very narrow, (.004") throat diameter range where maximum accuracy is obtained. Go smaller or larger and accuracy will suffer. By sim-

ply slipping the Plug Gauge into the barrel throat, it’s possi-ble to tell at a glance when you are approaching the correct diameter. Warns you before you go too far. Also valuable as a diagnostic tool for guns brought in with accuracy com-plaints, (designed for chamfers cut with our tools - may not give a correct reading on guns with other degrees of chamfer). Each gauge is self-piloted, precision-ground,

hardened and stepped to show minimum and maximum optimum diameters. 11° and 18° Gauge measures both chamfer angles. Sizes .22 RF; .32; .38/.357; .38-40/.40; .41; .44; .45. 5° Ruger-Style Gauge available in .38/.357, .44 and .45 caliber only. abSPECS: 11/4" (3.2cm) long. Steel. Instructions included. 11°-18° gauges measure forcing cones with either angle. 5°, .38/.357 gauge is designed for Ruger .38/.357’s which began using this angle about 1983. Complete Set includes the Rimfire Gauge, all ten Centerfire Gauges and Instructions in a Bench Kit Box.

BARREL CHAMFERING PLUG GAUGESHelps You Get Maximum Accuracy & Best

Results Using Pistol Chamfering Tools

STOCK # ANGLE CALIBER PRICE#080-580-132AS 11°-18° .32 Cal. 8K53E47 $ 68.47#080-580-138AS 11°-18° .38/.357 Cal. 8K48L73 $ 61.99#080-580-140AS 11°-18° .38-40/.40 Cal. 8K37A04 $ 49.95#080-580-141AS 11°-18° .41 Cal. 8K39Q40 $ 49.97#080-580-144AS 11°-18° .44 Cal. 8K44A06 $ 55.89#080-580-145AS 11°-18° .45 Cal. 8K60F00 $ 69.99#080-580-538AS 5° .38/.357 Cal. 8K39B02 $ 49.97#080-580-539AS 5° .44 Cal. 8K30E03 $ 37.19#080-580-540AS 5° .45 Cal. 8K30D03 $ 37.19#080-580-122AS Rimfire .22 Cal. 8K32A59 $ 39.95

#080-580-541AS 5° .44 & .45 Add-on Set, 8K52Q06 � � � $ 63.99#080-579-100AS Complete Plug Ga. Set, 8K211B79 � � � 255.99

QUESTIONS BEFORE YOU BUY?Call Or Email Our

Full-Time Tech Staff

PAGE 489Orders/Tech: 800-741-0015order on the web

brownells.com

SPE

CIA

LTY

N T

Many revolver barrels have only a bare minimum chamfer at the throat, no chamfer at all, or one that’s off center. Any of these conditions can spray lead and jacket material out of the barrel/cylinder gap, do strange things to the bullet shapes, and degrade accuracy. Plus, fouling will build up between barrel and cylinder, causing the cylinder to drag or lock up. Our Revolver Chamfering

tools are a custom, precision reaming system designed to help you cut a beautiful, chatter-free, perfectly centered chamfer without dismantling the barrel from the frame. The Extension Rod slides into the bore; screw on the Cutter; add the centering cone and the handle and you’re ready to go. All of the Kits let you choose the angle of the Chamfer Cutter, the size of the Facing Cutter and the Pilot. All include instructions and come in a see-through top box with plenty of room to start with a Basic Kit and add more components later. ab

.22 & .38 INTERMEDIATE CHAMFERING KITS

#080-496-232AS .22/.32 Master Chamfering Kit, 8K219J91 � � � � � � � � � � � � � � � � � � � � � � � � � $ 261.99

#080-494-022AS .22 Basic Chamfer Kit, 8K101D88 � � � 117.99#080-494-032AS .32 Basic Chamfer Kit, 8K113Q15 � � � 129.99

STK# .22 STK# .32 CUTTER DIA

PRICE

#080-495-400AS NA .400" 8K114Q31 $ 145.99#080-495-425AS NA .425" 8K110H98 $ 145.99#080-495-525AS NA .525" 8K113B29 $ 144.99

NA #080-496-400AS .400" 8K124G36 $ 140.99NA #080-496-425AS .425" 8K125P58 $ 140.99NA #080-496-525AS .525" 8K150F02 $ 159.99

.22 AND .32 CHAMFERING TOOL KIT PARTSINDIVIDUAL .22/.32 CHAMFERING TOOLS - Like their counter-parts for the larger calibers, these are also sold separately for re-placements and “build your own” chamfering tool sets.

#080-498-022AS .22 11° Chamfer Cutter, 8K34D31 � � � � �$ 41.96#080-498-032AS .32 11° Chamfer Cutter, 8K32Q28 � � � � 34.99#080-503-032AS .32 Pilot Bushing, 8K4D50 � � � � � � � � � � � 4.99#080-499-132AS .32 Center Cone, 8K4M85 � � � � � � � � � � � 5.99#080-500-400AS .400" .22/.32 Face Cutter, 8K33E61 � � � 41.40#080-500-425AS .425" .22/.32 Face Cutter, 8K34I27 � � � � 41.40#080-500-525AS .525" .22/.32 Face Cutter, 8K38L55 � � � 49.99#080-497-211AS .211" .22/.32 Pilot Shaft, 8K14Q76 � � � � 16.99#080-497-213AS .213" .22/.32 Pilot Shaft, 8K10D75 � � � � 12.99#080-497-215AS .215" .22/.32 Pilot Shaft, 8K10P75 � � � � � 12.99#080-501-000AS .22/.32 Chamfer Handle, 8K11D04 � � � � 14.97#080-485-000AS .22/.32 Breaker Bar, 8K5G09 � � � � � � � � � 5.99

BRASS LAPS - For those who want to put on the final touch of perfection. 5°, 11° and 18° brass laps are used with very fine abra-sive, which penetrates the brass and works as a final polish to the chamfer cuts.

STOCK # DEGREE FITS PRICE#080-499-220AS 11° .22 8K7E46 $ 9.99#080-499-032AS 11° .32 8K5N51 $ 7.99#080-499-033AS 18° .32 8K4Q74 $ 5.99#080-490-385AS 5° .38/.357 8K6M52 $ 7.99#080-490-455AS 5° .44 -.45 8K4M52 $ 5.99#080-490-381AS 11° .38 -.45 8K5C57 $ 7.99#080-490-388AS 18° .38 8K6B06 $ 6.99#080-490-458AS 18° .45 8K4H80 $ 5.99

pound angle. Use the .38 cutter for 9mm through .41; use the.45 cutter for .44 through .45.

82° Chamfer Cutter is used to lightly break the outside edge of the new chamfer.

90° Facing Cutter is another Ron Power “trick-of-the-trade”. Use to adjust barrel/cylinder gap, square the rear barrel face and eliminate high spots. Four Sizes: .540", for Ruger Security Six, GP-100; S&W K; Colt Mk III, Official Police; Charter Arms; .560", for S&W L; .625", for S&W N; Ruger Blackhawk, Super Blackhawk; .687", for Ruger Redhawk.

STOCK # TYPE DEGREE FITS PRICE#080-486-100AS Chamfer 5° .38 8K33C76 $ 43.99#080-486-500AS Chamfer 5° .44-45 8K35B84 $ 49.95#080-486-200AS Chamfer 11° .38-45 8K36D75 $ 52.99#080-486-300AS Chamfer 18° .38 8K41E38 $ 59.99#080-486-400AS Chamfer 18° .45 8K31D01 $ 39.97#080-486-382AS Chamfer 82° .38 8K30B37 $ 39.95#080-492-540AS Facing 90° .540 8K37E27 $ 52.99#080-492-560AS Facing 90° .560 8K27C02 $ 34.99#080-492-625AS Facing 90° .625 8K35N84 $ 49.95#080-492-687AS Facing 90° .687 8K46I18 $ 59.95

CHAMFERING TOOL KIT PARTS.38-.45 CHAMFERING KIT PARTS

#080-482-000AS Chamfer Tool Handle, 8K9M20 � � � � � � �$ 12.99#080-483-000AS Chamfer Extension Rod, 8K10D84 � � � � 14.99#080-484-000AS Chamfer Center Guide, 8K3I03 � � � � � � � 3.99#080-485-000AS .22/.32 Breaker Bar, 8K4L66 � � � � � � � � � 5.99#080-100-391AS Chamfer Kit Box, 8K20B18 � � � � � � � � � � � 25.99

CHAMFER TOOL PILOTS - Also a Ron Power suggestion. Remov-able brass pilots precisely center breech end of the Chamfer Tool Extension Rod to eliminate any possibility of cutter runout. They do not interfere with cutting action or chip removal. Seven sizes: .38 (.346"), .38-40 (.394"), .40/10mm (.388"), .41 (.398"), .44 (.416"), .45 (.422"), .475/.480 (.466").

.22 AND .32 CHAMFERING KITS.22/.32 CALIBER CHAMFERING KITS - The Master .22/.32 Kit in-cludes: (3) Pilot/Shafts (.211", .213", .215" diameter, 12" long) to hold and center cutters in .22 bores; 11°, .22 caliber Cutter; 11°, .22 Brass Lap; 11°, .32 caliber Cutter; 11°, .32 Brass Lap; 18°, .32 caliber Cut-ter, 18°, .32 caliber Brass Lap; .32 caliber Pilot Bushing; .32 caliber Centering Cone; three 90° Facing Cutters; K-22 Adapter and .32 Facing Cutter Adapter to allow use of larger facing cutters from .38-.45 Kits for larger frame .22's and .32's; Handle; Breaker Bar; Allen Wrench and Fitted Bench Box.

The .22 Basic Kit includes: 3 Pilot/Shafts; 11° Cutter, 11° Brass Lap; Handle; Breaker Bar; Allen Wrench and Fitted Bench Box. .32 Basic Kit has: .215" (5.46mm) diameter Pilot/Shaft; 11°, .32 Cutter; 11°, .32 Brass Lap; 18°, .32 Cutter, 18°, .32 Brass Lap; .32 Brass Pilot; Centering Cone; Handle; Breaker Bar, Allen Wrench and Fitted Box.

The Intermediate .22 and .32 Kits contain everything in the .22 or .32 Basic Kit, plus one 90° Facing Cutter of your choice as shown in the charts below.

.38-.45 CALIBER TOOLS.38-.45 CALIBER CHAMFERING KITS - To cover the “whole nine yards” there’s the Complete Gunsmith’s Chamfering Tool Kit. You get two 18° Chamfer Cutters, two 18° Brass Laps, the 11° Brass Lap, the 5° Brass Lap, the 11° Chamfer Cutter, the .38 cal. 82° Chamfer Cutter, .38 cal. 5° Chamfer Cutter, all four 90° Facing Cutters, all four chamfer tool Pilots and, of course, the Handle, Tool Extension Rod, Centering Guide, Breaker Bar, and 3/32" Allen Wrench . . . all in the fitted, plastic, box.

The Basic .38-.45 Kit consists of Handle, Tool Extension Rod, Centering Guide, one 11° or Chamfer Cutter, a cutter removing Breaker Bar, 3/32" Allen Wrench and the Kit Box.

The Intermediate .38-.45 Kit adds one Facing Cutter and one Pilot of your choice to the Basic Kit.

INTERMEDIATE .38-45 CHAMFERING KITS

#080-481-000AS Complete .38 - .45 Chamfering Kit, 8K230L61 � � � � � � � � � � � � � � � � � � � � � � � � $ 255.95

#080-479-451AS Basic Chamfering Kit, 8K62H86 � � � � 81.99

STOCK #90° FACING

CUTTER DIA. PILOT PRICE#080-480-251AS .540" .38 8K96K01 $ 137.99#080-480-261AS .560" .38 8K95P77 $ 130.99#080-480-271AS .625" .38 8K94G52 $ 134.99#080-480-281AS .687" .38 8K94A52 $ 134.99#080-480-252AS .540" .41 8K66D07 $ 81.99#080-480-262AS .560" .41 8K65I77 $ 80.99#080-480-272AS .625" .41 8K65B77 $ 80.99#080-480-282AS .687" .41 8K65P77 $ 80.99#080-480-253AS .540" .44 8K66N07 $ 81.99#080-480-263AS .560" .44 8K65B77 $ 80.99#080-480-273AS .625" .44 8K65K77 $ 80.99#080-480-283AS .687" .44 8K65B77 $ 80.99#080-480-254AS .540" .45 8K66K07 $ 81.99#080-480-264AS .560" .45 8K65N77 $ 80.99#080-480-274AS .625" .45 8K65C77 $ 80.99#080-480-284AS .687" .45 8K65P77 $ 80.99

INDIVIDUAL CHAMFERING TOOLSINDIVIDUAL .38-. 45 CHAMFERING TOOLS - Also sold separately for replacements and “build your own” chamfering kits.

5° Chamfer Cutter has a super gentle angle as currently used by Ruger on their .38/.357 DA guns. If you set back a Ruger barrel or just want to duplicate this angle on any other barrel, use this cutter. You CANNOT use 18° or 11° cutters on a 5° throat without exceed-ing maximum throat diameter or making a compound angle.

11° Chamfer Cutter is recommended by Ron Power. The gen-tler entry angle causes less bullet deformation and gives better accuracy (especially important for “wadcutter” shooters). One size for all calibers from .38 to .45. Use with pilots in chart.

18° Chamfer Cutter is our “standard” cutter. The angle is right for jacketed bullets as well as round nose and semi-wadcutter ablead bullets. It will remove most factory cuts without exceeding the maximum recommended throat diameter or creating a com-

REVOLVER CHAMFERING TOOLS & KITSCuts Beautiful, Chatter-Free Chamfer To Eliminate Bullet Splatter, Shaving, and Fouling Buildup - No Lathe Needed, No Need To Remove Barrel From Frame

STOCK # FITS#080-493-001AS .38#080-493-005AS .38-40#080-493-006AS .40/10mm#080-493-002AS .41

STOCK # FITS#080-493-003AS .44#080-493-004AS .45#080-493-007AS .475/.480

— Advise # — Chamfer Tool Brass Pilot, 8K6L28 � � � � � � � �$ 8.99

SHO

P SU

LIES

Keep all the info about each one of your guns together. Heavy paper folder has space for: usual data, plus, info on scope, sling, and alterations. Each folder comes with its own polypropylene page protector.SPECS: 81/4" x 11" sheet in 9" x 111/2" bag. Sold in Pak of 25.

PERSONAL FIREARMS LOG

Organize Your Personal Guns Data

#084-225-000AS Personal Firearms Log, 4H13M92 � � � � $ 14.99

Made from the best grade, tightly woven, 2-ply yarn, all-cotton duck—the same stuff they make top quality, insulated coveralls from. Solvent- and oil-proof nylon thread used throughout. Every-thing heavily reinforced with seams rolled, double stitched and fin-ished, all corners and stress points bar-tacked for strength. Machine washes and dries without edges curling or losing shape. ab

LONG SHOP APRON - Cov-ers from shoulders to below the knees to keep dirt /crud off your clothes. Adjustable hook and loop neck strap for a custom fit. Neck and rear tie straps are dou-ble thickness for extra strength. Three pockets: a centered upper one with a sewn-in pencil slot and large lower ones on the left and right sides. O-Ring model fea-tures neck straps sewn together as a halter and metal O-rings that help adjust the bib for maximum coverage.SPECS: 391/2" (100.3cm) long, 301/2" (77.5cm) wide. Pockets: Top - 47/8" (12.4cm) wide x 43/4" (12cm) high with pencil slot. Lower (x2) - 73/4" (19.7cm) wide by 63/4" (17.1cm) high. Ties: each 271/2" (69.8cm) long. Neck strap: 213/4" (55.2cm) long. O-Ring model has 1" (2.5cm) O.D. metal rings at top corners.#084-071-000AS Brownells Long Shop Apron,

4A27B84 � � � � � � � � � � � � � � � � � � � � � � � � � � �$ 33.99#084-071-001AS Long Premium Shop Apron With

O-Ring, 4A33E74 � � � � � � � � � � � � � � � � � � � 37.99

SHORT SHOP APRON - Top-quality, custom-made, above-the-knees apron. Hook-and-loop closure on the neck strap lets you adjust the “bib” for maximum cover-age and the length to match wear-er’s height. Centered top pocket is sewn solidly to the apron so it can’t swing and has a separate slot for pens, pencils, or a mike. Roomy, double, lower pockets. O-Ring model features neck straps sewn together as a halter and metal O-rings that help adjust the bib for maximum coverage. SPECS: 281/2" (72.4cm) long. 2" (63.5cm) wide. Pockets: Top - 41/8" (10.5cm) wide x 41/4" (12cm) high with pencil slot. Lower (x2) - 63/4" (17.1cm) wide x 61/4" (15.9cm) high. Ties: each 271/2" (69.8cm) long. Neck strap: 213/4" (55.2cm) long. O-Ring model has 1” (2.5cm) O.D. metal rings at top corners.#084-071-050AS Brownells Short Shop Apron,

4A28P51 � � � � � � � � � � � � � � � � � � � � � � � � � � � �$ 32.99#084-071-051AS Short Premium Shop Apron With

O-Ring, 4A31I60 � � � � � � � � � � � � � � � � � � � � 35.99

PREMIUM SHOP APRONSTop Quality, Custom-Made For The Professional Gunsmith

(PDF) LISLE GARTHWAITE BROWNING HI-POWER C.B. … · GARTHWAITE BROWNING HI-POWER ARMORER’S TOOLS The Right Tools For Proper Disassembly & Assembly #100-007-006AS Browning Hi-Power Armorer’s - DOKUMEN.TIPS (2024)

FAQs

What's so special about Browning Hi-Power? ›

Is the Browning Hi-Power single stack? ›

References

Grading	100%	70%
MSR $1,245	$1,125	$500
MSR $1,245	$1,125	$500
MSR $1,245	$1,125	$500